-
Gauntlet Barrel Baffle Spring
Umarex Gauntlet Baffle Spring
$7.00Select optionsUmarex Gauntlet .177, .22, or .25 Baffle Spring.
Part is not compatible with Gauntlet .30 Caliber
This is the spring that lives in your Gauntlets Shroud. It is required to keep the air stripper on the end of the barrel and allows the baffle or baffle stack to live under tension.
-
Burst Disk Two Pack
Regulator Burst Disks 1.8k, 3k, 5k & 7.5k
$9.95Select options- 1.8k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 3k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 5k burst disk is used as the high-pressure burst disk on 3k tanks
- 7.5k burst disk is used as the high-pressure burst disk on 4.5k tanks
Actual burst disk finish may be Black, or Bright depending on availability.
-
Sale!
QD PORT SLING SWIVEL AND BASE
$14.99Original price was: $14.99.$9.99Current price is: $9.99. -
for .177, .22 and .25 NOT .30
Umarex Gauntlet Aluminum Air Stripper
Rated 5.00 out of 5$12.00Select optionsThis part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.
Part does not fit Gauntlet .30 caliber
This part is designed and manufactured by DonnyFL
-
Sale!
Stock Umarex Magazine
Umarex Gauntlet Rotary Magazine
$17.95Original price was: $17.95.$14.00Current price is: $14.00.The Gauntlet Rotary Magazine advances each pellet with the operation of the bolt on the Umarex Gauntlet PCP air rifle.
Features
- .177 = 12 shots
- .22 = 10 shots
- .25 = 8 shots
- .30 = 7 shots
-
Bipod and Picatinny Rail
$15.00 – $70.00Select optionsInstallation Video for 1.5″ Picatinny rail on the Umarex Gauntlet forearm.
-
Gauntlet 1 and Gauntlet 2
Umarex Gauntlet Tune O-ring Kit
$17.00Select optionsHajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
-
Umarex Gauntlet Regulator Shim Pak
$18.50Select optionsHajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
-
HP Baffle Stack For Umarex Gauntlet
Rated 5.00 out of 5$20.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.
-
HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
Rated 5.00 out of 5$28.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.
Air Stripper comes with o-ring and silicone grease for installation.
-
Fits Gauntlet 1, 2 even the .30 Cal
HP Barrel Band For Umarex Gauntlet
Rated 5.00 out of 5$30.00 – $35.00Select options -
Intended for higher power builds
High Travel Valve Stop For Umarex Gauntlet 1 or 2
$30.00Select optionsThis part replaces part #19 and allows for greater valve dwell producing more power to be produced at higher regulator pressure settings.
The .22 caliber HTVS for the Generation 1 Gauntlet fits both the .177 and .22. Do not order Generation 1 HTVS for the Generation 2 Gauntlet, they are not the same
-
Gauntlet 1 or Gauntlet 2 Mini Magazine
HP Gauntlet, Mini Mag
$33.00Select optionsIntroducing the HP Mini Magazine.
The same reliable design as our expanded magazine but shorter to allow the mag to fit under your optic without the need to adjust or swap out your scope rings.
The HP Mini magazine is designed to fit the Umarex Gauntlet 1 or 2 in .22 and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload.
The stands only 40.90mm (1.610″)
The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell, maybe
Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .22 = 13 shots
- .25 = 11 shots
- The magazine height is 40.90mm (1.610″ )
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
-
For Gauntlet .177, .22, .25 and .30 Calibers
Hajimoto’s Gauntlet Expanded Magazine
Rated 4.00 out of 5$35.00 – $40.00Select optionsHere is a high-quality, high-capacity magazine designed to fit the Umarex Gauntlet 1 or 2 in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjust rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.
The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell
Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .177 – 21 shots which is an increase of 110% more shots over the stock magazine!
- .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
- .25 = 15 shots which is an increase of 37.5% more shots over the stock magazine!
- .30 = 11 shots which is an increase of 57.5% more shots over the stock magazine!
- The magazine height for the .177, .22 and .25 is 50.25MM (1.978″)
- The magazine height for the .30 is 46.20MM (1.820″) Max Slug/Pellet length supported 11.20mm (0.441″)
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
-
Fits both Avenger and Origin
HP Avenger Exp Mag
$35.00 – $40.00Select optionsHere is a high-quality, expanded capacity magazine designed to fit the Umarex Origin in .22 & .25 calibers as well as a version for Air Venturi Avenger in .177, .22 and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjust rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.
The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell
Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .177 (Avenger only) – 21 shots which is an increase of 110% more shots over the stock magazine!
- .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
- .25 = 15 shots which is an increase of 87.5% more shots over the stock magazine!
- The magazine height of all calibers is 50.25MM (1.978″)
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
-
Replacement end caps
Emperor/Ronin End Caps
$35.00Select optionsTHIS IS AN AIRGUN ONLY PART
Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.
-
For the Gauntlet 1 or 2
Umarex Gauntlet 1/2 x 20 adapter #A23
$40.00Select optionsThis part is designed and manufactured by DonnyFL
-
Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
$40.00Select optionsFits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s
This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.
If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.
This part is designed and manufactured by DonnyFL
-
Akela/Kratos Strip Stak Pak
HP Strip Stak Pak for Akela/Kratos
$40.00Select optionsINCLUDES NEW ENHANCED AIR STRIPPER DESIGN
Strip Stak Pak for the Benjamin Akela and Kratos PCP’s
A nine-piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides variable-sized baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A8 adapter.
The Air Stripper is threaded and comes with an o-ring and silicone grease for installation. The stock barrel shroud spring must be reused.Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
for .177, .22 and .25 NOT .30
Umarex Gauntlet Strip Stak Pak (Bundle)
$45.00Select optionsHajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.
Air Stripper comes with o-ring and silicone grease for installation.
-
Regulator Service or Pressure Change
Regulator Service or Pressure Change
$45.00Select optionsThis is a service to repair, test, leak test, adjust or increase the output pressure of a Umarex Gauntlet 1 or 2, regulator to a customer’s requested output. The regulator will be tested and calibrated to within +/- 75 PSI. Parts such as Gauges, Burst discs, Bonnets, Pistons, Caps, or Regulator bodies are not included. If parts are determined to be required to repair the regulator, pricing will be determined, quoted, and will need to be paid prior to the return of the regulator.
Please note that if you have a Taiwan-produced regulator, which is the regulator that is located at the top of the photo, there are very limited corrections that can be made to these units and you may end up needing a new regulator. Please use the notes area to provide the Generation and caliber of the rifle. Also, give as much detail as possible of the issue or the requested pressure output and so forth.
Once the order is physically reviewed, you will receive a second notification with details associated with packaging and shipping the items in for service.
When you place the order for the above-described service, you will receive an order processing notification. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your regulator or regulator and tank assembly.
This service is not a hydro test of the tank/bottle and is focused only on the regulator’s functionality and visual inspection assemblies.
Please note that this service is not associated with any manufacturer’s warranty, so please be sure to exhaust all warranty options prior to sending us your regulator for service as our working on the part voids any manufacturer-provided warranties.
-
Umarex Origin 1/2 x 20 Adapter #A70
$45.00Select optionsSpecifically for the Umarex Origin
Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.
This version allows you to use a larger suppressor than the Tanto or KOI. Designed to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.
This part is designed and manufactured by DonnyFL
-
Origin .22/.25
HP Strip Stak Pak for Origin
Rated 4.33 out of 5$47.00Select optionsNEW ENHANCED DESIGN
UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
Gauntlet Bottle Shroud Mod
$50.00 – $60.00Select optionsThis service is to modify the bottle shroud to allow the proper fit for the Power Flex Combo carbon fiber tank and flex regulator:
The service can be added to an existing tune/build or a stand-alone ship in service. If you are shipping me your forestock or bottle shroud be sure to keep the screws, star washers, and sling stud as I will not need those. If you have any type of rail installed for a bipod it needs to be removed prior to shipping me the bottle shroud.
If you select the stand-alone ship service, shipping instructions will follow which detail the packaging and address to ship to.
Cerakote or color change is not included photo is from the 2021 Hajimoto Edition for illustration purposes.
-
For G30, G30SL or Any Gen Gauntlet
Gauntlet Barrel Chambering Correction
$50.00Select optionsService to correct the Gauntlet series of PCP’s. Calibers include .177, .22, 25, 30, or the 30SL, hard chambering of slugs issues.
-
Trigger work
$55.00Select optionsThe service can be added to an existing tune/build or a stand-alone ship in service. If you are shipping me your trigger group, you simply decock and degas the Gauntlet, remove it from the stock, and remove the two fasteners that hold the group to the bottom of the pressure tube.
If you elect the stand-alone ship service, shipping instructions will follow which detail the packaging and address to ship to.
-
for .177, .22 and .25 NOT .30
Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter
Rated 5.00 out of 5$60.00Select optionsPart fits Umarex Gauntlet 177, .22 or .25. Not compatible wit the Gauntlet .30 Caliber.
This part is designed and manufactured by DonnyFL
-
Gun Stock Mod for Super Tune Kit
$60.00Select optionsThe service of modifying your Gauntlet gun stock does not include shipping. Return shipping will be calculated and added at check out. Shipping cost will be based on a complete rifle sent to Hajimoto Productions in the original box and packing materials. If only the rifle stock is received and is in something lighter than the typical 14lbs, shipping credits will be applied prior to the rifle being shipped back to the customer. If the rifle is received in something heavier than the typical 14lbs, additional shipping costs will need to be paid prior to the rifle being shipped back to the customer.
-
V3 6.26 inch Extension
Emperor/Ronin Extender
$60.00Select optionsTHIS IS AN AIRGUN ONLY PART
Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it’s the latest model.
-
Gauntlet Regulator Tester
$65.00Select optionsAssembled and tested by Hajimoto using quality US Parts! Don’t guess what the output of your Gauntlets regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.
Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like these shown
-
Install Super Tune Kit
$70.00Select optionsPlease note that these are services to your rifle and not just the parts. If your looking for parts only head to the PRODUCTS section of the website.
The service of installing the Super Tune Kit does not include shipping. Return shipping will be calculated and added at check out. Shipping cost will be based on a complete rifle sent to Hajimoto Productions in the original box and packing materials. Stock modification is part of the STK install which is why you need to send the entire rifle to us not just the action. If the rifle is received in something heavier than the typical 14lbs, additional shipping costs will need to be paid prior to the rifle being shipped back to the customer.
-
Sale!
Gauntlet STK
Super Tune Kit (STK) for Gauntlet 1 and 2
Rated 5.00 out of 5$75.00 – $85.00Select optionsTHIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCKThe single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!
Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)
For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLETCONTENTS:
- Adjuster Plug Assembly.
- Smaller, Lighter Composite Poppet.
- Hajimoto Hammer Spring (Black Long)
- Lighter Trigger Spring (Bright Small).
- 5/64″ Allen Wrench For Adjusting Power.
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:Written Detailed Tuning Instructions for the STK
More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there. -
FX No Limit Scope Rings 1″, 30mm and 34mm
$79.00 – $99.00Select optionsFX shows that they are able to innovate not just within airguns themselves, but in other areas of the shooting sports. The FX No Limit scope rings are perfect for long-range shooting as you can vertically adjust and angle your mounts so you can always find the sweet spot on your scope. These rings are also very useful if you need to have your scope higher off the receiver to allow for oversized magazines or scope camera setups.
You will want these rings if you are planning on using my Expanded Magazine.
-
Gauntlet O-ring service
$95.00Select optionsThis service tears the entire air rifle down, cleans and inspects for part wear, and replaces all the o-rings in your Gauntlet. Whether the o-rings are leaking from age or wear, whether the rifle is actually leaking or not, all o-rings are replaced. The rifle undergoes an incoming inspection which captures the functional and physical condition of the air rifle. This information is presented in a report which must be reviewed and approved prior to any work can begin.
The o- rings that are replaced are:-
- (2) Regulator to gun o-rings.
- (1) Stock end cap o-ring.
- (1) Stock air stripper o-ring.
- (1) Barrel to shroud support collar at breach block o-ring.
- (2) Bottle block to pressure tube o-rings.
- (1) Valve body o-ring.
- (2) Pellet probe o-rings.
- (3) Barrel to breach block o-rings.
The action is verified and lubricated prior to returning the rifle. The rifle undergoes a pressure test for 24 hours to guarantee there are no pressure losses.
-
-
Tanto 1.22 x 5 inches
Tanto 1.22 x 5 inches
$99.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Fits the G1, G2 or G30
Real 2 Stage Trigger for the Gauntlet
Rated 5.00 out of 5$110.00Select optionsFull-fledged 2-stage trigger for the Umarex Gauntlet 1, 2 or G30. This trigger is a direct replacement for the single-stage trigger that ships with the Umarex Gauntlet. This trigger is a straightforward install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
- The Trigger Is Stainless Steel 17-4 Through Hardened
- The Trigger Shoe Is Aluminum 6061-T6
Please see the installation video below for more details.
Super Tune Kit Users
You must use the stock trigger return spring with the two-stage trigger as the trigger spring that comes with the Super Tune Kit is too light to be effective with the two-stage trigger. -
For G30 and G30SL
G30 Barrel Shorten and Recrown
$110.00Select optionsService to reduce barrel length removing the barrel choke making the barrel better for slugs.
-
DonnyFL FX Suppressor
FX/DonnyFL 1.36 x 5 inches
$120.00Select optionsTHIS IS AN AIRGUN ONLY PART
This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
Rated 5.00 out of 5$130.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
for .177, .22 and .25 NOT .30
Gauntlet Short Shroud Combo
$130.00 – $215.00Select optionsThis part is designed and manufactured by DonnyFL for airgun use only
Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber
Stock baffle spring must be used!
Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.If Your Gauntlet is:
- .177 Get a .177/.22 Supressor
- .22 Get a .22/.25 Supressor
- .25 Get a .25/.30 Supressor
Get it?
-
NEW MODEL
Pro V3 for 3K and 4.5K Cylinders
Ninja Pro V3 Regulator 5/8″ Thread
$148.00Select optionsThe All New Hajimoto Pro V3 in 5/8”-18UNF Thread with Stainless Steel Cap Threads
Ninja's Pro V3 with rotional bonnet. A perfect replacement for the regulator found on the on the Gauntlet 2. A complete regulator rebuild kit is included! MADE IN THE USA! Ninja regulator output pressures in increments of 100PSI. Simply select your desired output pressure. Output ranges from 1100PSI to 2400PSI. All custom built pressure units will have a +/- 50 psi tolerance.
-
5/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
$149.00 – $159.00Select optionsNewly redesigned unit
Now has a high pressure and low pressure burst discs!
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800PSI adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF
The Ninja Flex regulator is available in any 900PSI spread to a maximum of 3100PSI output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex RegFlex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/700 to 1500PSIFlex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1600 to 2400PSIFlex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSIComes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
-
Sumo 1.6 x 6.25 inches
$150.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
NEW MODEL
PRO V3 REG WITH 13CI TANK
Ninja 13ci 3000PSI Air Tank with Pro V3 Regulator
$155.00Select optionsIncludes Hajimotos Pro V3 regulator with Stainless Steel Threaded rotional Cap. Say goodbye to gauges and foster nipples not lining up with the stock openings when the is installed tight. A complete regulator rebuild kit is included!
This is an aluminum 13ci bottle that holds 3000PSI including a Pro V3 regulator with custom output pressures in increments of 100PSI. Simply select the desired pressure in the dropdown. Pressure Recommendations For Umarex Gauntlet Generation 1 .177, .22 and .25 Stock Gauntlet Gen1 .177/.22 | 13ci/3000/1100PSI Regulator Gauntlet with STK Installed .177/.22 | 13ci/3000/1400PSI Regulator Stock Gauntlet Gen1 .25 | 13ci/3000/1900PSI Regulator Gauntlet with STK Installed .25 | 13ci/3000/2100 Regulator
-
Flex Reg on 13ci Aluminum 3K
Gauntlet Flex Reg with 13ci Tank – Hajimoto Configurations
$169.00Select optionsIntroducing a Hajimoto Productions Exclusive offer!
13ci/213cc/.21L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 13 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSIFlex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1600 to 2400PSIInstalls on the Gauntlet with minor tank shroud modifications.
A 13ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg with typical G1/2-14 threads connects to your Umarex Gauntlet 1 or Gauntlet 2 without any modifications!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 13 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
-
NEW MODEL
PRO V3 ON 22ci 3K Cylinder
Ninja 22ci 3000PSI Air Tank with Pro V3 Regulator
$173.00 – $175.00Select optionsIncludes Ninja’s Pro V3 regulator with Stainless Steel Threaded 36o° rotational Cap.
Say goodbye to gauges and foster nipples not lining up with the openings in the stock.This is an aluminum 22ci bottle that holds 3000PSI including a Pro V3 regulator with custom output pressures in increments of 100PSI. Simply select the desired pressure in the dropdown.
PRESSURE – STOCK AND RECOMMENDED
Stock .177/.22 | 22ci/3000/1100PSI Regulator
Super Tuned .177/.22 (IF STK IS INSTALLED) | 22ci/3000/1400PSI RegulatorStock .25 | 22ci/3000/1900PSI Regulator
Super Tuned .25 (IF STK IS INSTALLED) | 22ci/3000/2100 RegulatorThis setup is for the original Umarex Gauntlet 1 with the Black stock.
A complete regulator rebuild kit is included!
NINJA REGULATORS ARE MADE IN THE USA!
-
Sold out!
2 x 4.25 inches Fatboy 2.0
Fat Boy 2 x 4.25 inches
$175.00Read moreTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
2 x 4.25 inches Fatboy 2.0
Take the width of the Ronan or Emperor and the length of the Tatsu then mix in some super cool modularity components and you end up with the Fat Boy. In the 2.0 version, we gave this Campbell soup can a face lift. New outer shell design along with interchangeable calibers from .177 up to .30. Shooters who wanted something short yet effective, the Fatboy will surprise you.
Features:
- Compatible with .177 to .30 calibers
- Includes 3 interchangeable air strippers
- Redesigned 1/2 x 20 rear cap for easy gripping
- Can be used with the 6.25 inch extender for more hush power
- Measure 4.25 inches long by 2 inches in diameter
- Weighs only 6.7 oz
-
Shogun 1.6 x 8 inches
$185.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end. -
Ronin 2 x 6.25 inch
Rated 5.00 out of 5$185.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL out of high-quality 6061 Aluminum.
The Ronin is made to quiet the big dogs. The Ronin is best on a high power .25 caliber or a Gauntlet .30 Caliber.
We only stock the .22/.25 , .25/.30 caliber, and .357 in 1/2 x 20 UNF threaded versions.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
The .357 is for shrouded barrel .30 calibers or direct barrel threaded .357 caliber PCPsIf you are looking to make the Ronin or Emperor really quiet, consider the 6.25″ Ronin extension chamber for extra stealthiness.
-
Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
$195.00Select optionsIntroducing a Hajimoto Productions Exclusive offer!
22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSIFlex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSIIf you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE
Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
-
Sale!
Installation of our Sidelever on G2 or G1
Gauntlet Sidelever Install
$220.00Original price was: $220.00.$195.00Current price is: $195.00.This service is for the installation of our sidelever cocking system installed in your action. The Sidelever is no longer being offered for .30 caliber variants.
Our side lever system eliminates one of the main gripes folks have with the Umarex Gauntlet and that is COCKING EFFORT!
There is no comparison in cocking effort when you apply the mechanical advantage a sidelever gives you. The installation is a non-destructive installation and can be reversed without any compromise to the airgun’s action or stock.
The sidelever system is a CNC milled 6061 Aluminum part which is hard anodized for a great match to the existing Gauntlet finish. The cocking vertical handle is an additive manufactured carbon fiber & ABS part that can be swapped out by you if you wanted to use a custom handle from wood or other material.
Our sidelever cocking system does require that you hold the handle back to swap mags but there is no need to hold back if you single load using the single shot tray.
One of the most common questions we get is “Can I just buy the parts and install them myself?” and the short answer is, no you cannot. For the reasons why, please read the ARTICLE we published in our blog in February 2023 on this topic.
See below for detailed shipping instructions and preparation videos.
-
Sale!
0.5L/500cc CE Certified CF Tank
0.50L Carbon Fiber Tank 4500PSI
$260.00Original price was: $260.00.$220.00Current price is: $220.00. -
DonnyFL EMPEROR V3 Moderator
Emperor 2 x 11 inch
$239.99Select optionsTHIS IS AN AIRGUN ONLY PART
Introducing the largest DonnyFL suppressor catered to the big bore guns.
Overall length 11 inches and weighs in at 1 lb.
This thing is built like a tank to tame those power hungry shooters.
-
4.5K PSI Ninja Reg on a 18ci/295cc/.29L CE Certified CF Tank
Ninja Reg on 18ci Carbon Fiber Bottle
$274.00Select optionsDirect replacement with no modifications required for the Umarex Gauntlet 2!
18ci/295cc/.29L 4500 PSI Carbon Fiber Bottle
Hajimoto is bringing sexy back! Doesn’t that carbon fiber look awesome on there!
Includes Ninja’s HP regulator.
The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This 4500 PSI carbon fiber bottle is 18ci and is absolutely gorgeous on the Gauntlet 1 or Gauntlet 2.The Gauntlet 1 will need to have its tank shroud inside diameter increased to allow the foregrip/tank cover to side over this carbon fiber tank.
Operating Pressure Recommendations
Gauntlet 1:
.177/.22 Stock operating pressure 1100PSI Max Recommended pressure is 1400PSI.
.25 Caliber Stock operating pressure 1900PSI Max Recommended pressure is 2100PSI.
Gauntlet 2:
.22 Stock operating pressure 1900PSI Max Recommended pressure is 2100PSI.
.25 Caliber Stock operating pressure 2100PSI Max Recommended pressure is 2300PSI.NINJA REGULATORS ARE MADE IN THE USA!
-
Sale!
0.7L/700cc CE Certified CF Tank
0.70L Carbon Fiber Tank 4500PSI
$390.00Original price was: $390.00.$280.00Current price is: $280.00.0.7L/700cc CE Certified CF Tank
Perfect fit for your custom build.
M18x1.5 Threaded
If you plan to use this bottle with a Gauntlet, you must remove and leave removed, the tank shroud. This bottle cannot use the flex reg as it is threaded M18.
Consider our barrel bands for the 500cc and 700cc bottles on the Gauntlet found HERE
-
NEW MODEL
PRO V3 Reg on a 22.5ci/370cc/.37L CE Certified CF Tank
Ninja Pro V3 Reg on 22.5ci Carbon Fiber Bottle
$294.00Select optionsALL NEW!
Direct replacement with no modifications required for the Umarex Gauntlet 2 and Gauntlet 30 Cal!
22.5ci/370cc/.37L CE Certified CF Tank
Shaves off 1/2 a pound of weight compared to the 4500psi stock aluminum tank.
A complete regulator rebuild kit is included!
Includes the New Hajimoto Pro V3 regulator with Stainless Steel rotational bonnet.
Say goodbye to gauges and foster nipples not lining up with the openings in the stock.The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This 4500 PSI carbon fiber bottle is 22.5ci and is absolutely gorgeous on the Gauntlet series of PCP.
The Gauntlet 1 will need to have its tank shroud inside diameter increased slightly to allow the foregrip/tank cover to side over this carbon fiber tank or simply remove the tank shroud.
Operating Pressure Recommendations
Gauntlet 1:
.177/.22 Stock operating pressure 1100PSI Max Recommended pressure is 1400PSI.
.25 Caliber Stock operating pressure 1900PSI Max Recommended pressure is 2300PSI.
Gauntlet 2:
.22 Stock operating pressure 1900PSI Max Recommended pressure is 2150PSI.
.25 Caliber Stock operating pressure 2100PSI Max Recommended pressure is 2400PSI.NINJA REGULATORS ARE MADE IN THE USA!
-
Sold out!
Flex Reg on 18ci/295cc/.29L CE Certified CF Tank
Power Flex Combo 18.3ci Carbon Fiber 4500PSI
$339.00Original price was: $339.00.$295.00Current price is: $295.00.Introducing a Hajimoto Productions Exclusive offering!
18ci/295cc/.29L CE Certified CF TankFits the Gauntlet 2 without any modifications.
The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. An 18.3ci carbon fiber 4500PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet! The massive volume of air afforded you is mind-blowing.
The diameter of the tank is 54-55mm across so a modification to the forearm is required if you desire to continue to use the Gauntlets tank shroud. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
Gauntlet Bottle Shroud Mod
Please see the examples provided in the accompanying photos.
The Gauntlet 2 forearm slides right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom. Please be careful if you have accessories on any of the MLok openings as the screws or MLok fasteners may scratch the tank when the shroud is slid forward or back.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!.
The cylinder’s outside dimension is slightly larger than the stock aluminum tank so my standard HP Barrel Band does not fit. You will need to use the HP Barrel Band CFT version
Regulator is Made in the USA! The Power Flex Combo is set to either of the two Gauntlet configurations. Simply select the proper configuration. Power Flex Combo Configuration For .177/.22 Cal Flex Reg set to 700 to 1500PSI
Power Flex Combo Configuration For .25 Cal Flex Reg set to 1600 to 2400PSI
DO NOT USE Power Flex Combo Configuration For .25 CONFIG on .177 or .22 they are not capable of handling the pressures. Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
-
Range & Power Trend Service
$310.00Select optionsThis is the service that is included with the Gauntlet 1 Platinum Package as well as the Gauntlet 2 Gold, Platinum, and Ultimate packages. The service is an add-on for lower airgun package offerings that run the rifle through a series of shooting exercises in order to capture and chart power generation and accuracy. This service produces the actual targets shot by your rifle at 25 and 50 yards on 2″ targets. The responses that you provide during the questionnaire are what we use during the final adjustment and execution phases.
You will receive a detailed build sheet that captures every detail of what was performed on your air rifle. You will also receive a detailed data matrix and range result sheet which has the power generation matrix with different ammo weights, feet per second, foot-pounds of energy developed, and what the power adjuster was set to in order to develop those results.
These data sheets become a quick reference for baseline performance data that you can always refer to in order to understand where your power adjuster should be in order to achieve the stated results.
-
Sale!
Flex reg and 22.5ci/370cc/.37L CE Certified CF Tank
Power Flex Combo 22.5ci Carbon Fiber 4500PSI
$375.00Original price was: $375.00.$330.00Current price is: $330.00.Introducing a Hajimoto Productions Exclusive offer!
22.5ci/370cc/.37L CE Certified CF Tank
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Installs on the Gauntlet 2 with minor tank shroud modifications, forearm slides right over the carbon fiber cylinder. Installation video at the bottom of the page.
The CF Tank is CE Certified and made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This included a 22.5ci carbon fiber 4500PSI cylinder with externally adjustable Ninja Flex Reg for your custom build including the Umarex Gauntlet 1 or Gauntlet 2! The massive volume of air in these 22.5ci tanks is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
Please be careful if you have accessories on any of the M-Lok openings as the screws or MLok fasteners may protrude into the tank area and scratch the tank when the shroud is slid forward or back. We recommend that if you have any MLok accessories installed, you remove them when sliding the shroud on or off. We also recommend covering the brass inserts in the tank shroud with cloth tape to protect your carbon fiber finish.
The Gauntlet 2 forearm slides right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom. See photo below
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex regulator on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 75PSI to the requested output.
-
Sale!
Flex reg and 30ci/500cc/.5L CE Certified CF Tank
Power Flex Combo 30ci/.5L Carbon Fiber 4500PSI
$349.00 – $360.00Select optionsPlease note that this combo will not fit a Gauntlet or Gauntlet 2 as the tank diameter is larger than the rifle’s tank shroud will allow. This combo is intended for builds that do away with the tank shroud or to be used on other PCP’s that allow for a typical paintball regulator installation.
Introducing a Hajimoto Productions Exclusive offer!
30ci/500cc/.5L CE Certified CF Tank
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This includes a 30ci/500cc/.5L CE Certified 4500PSI cylinder with externally adjustable Ninja Flex Reg for your custom build.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 900PSI!
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 75PSI (3.5bar) within the requested output.
-
Sale!
Ninja High Pressure Metric M18 Custom Output with Carbon Fiber Tank
Ninja High Pressure Metric M18 Custom Output with Carbon Fiber Tank
$360.00 – $419.00Select optionsAwesome configurations if you don’t care if the Gauntlet bottle shroud stays off. The 700cc on the G30 is beast mode!!!
Ninja Paintball High Pressure Regulator mounted on a quality 0.5L (500cc) or 0.7L (700cc) a 4500PSI rated Carbon Fiber Cylinder.
We build the regulator to any custom output pressure in 100 PSI increments from 1100PSI to 3100PSI
All custom built pressure units will have a +/- 75 psi tolerance.
-
Hajimoto Tune My Gauntlet G1 or G2
$625.00Select optionsWe completely tune your supplied Gauntlet 1 or 2 which includes everything listed in the section below.
The service includes a very detailed and time-consuming incoming inspection report that includes photos and other relevant information that detail the condition of the airgun and all of its pieces and parts. This report is provided to you and you must be reviewed and authorized in order for the work to continue.
Ordering procedures:
- Add all services and items to your cart.
- Be sure to use the notes section to communicate any known issues or special instructions.
- Check out.
Shortly after the order is received, you will receive an email notification containing shipping information that will include labeling and packaging requirements.
To better understand how the Gauntlet is transformed from a static you get what you get type of airgun, into an adjustable power and tunable PCP, take a look at this video that demonstrates how the power adjuster works if you should want to increase or decrease the power output for any given ammunition in order to get it to fly at the best rate of travel for that particular ammunition.
HOW TO ADJUST POWER WITH STKWe will build your order based on the information provided from the questionnaire as well as any specific requests, and before the airgun ships, any credits or additional charges will be settled.