-
DonnyFL FX Suppressor
FX/DonnyFL 1.36 x 5 inches
$120.00Select optionsTHIS IS AN AIRGUN ONLY PART
This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
Rated 5.00 out of 5$130.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
for .177, .22 and .25 NOT .30
Gauntlet Short Shroud Combo
$130.00 – $215.00Select optionsThis part is designed and manufactured by DonnyFL for airgun use only
Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber
Stock baffle spring must be used!
Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.If Your Gauntlet is:
- .177 Get a .177/.22 Supressor
- .22 Get a .22/.25 Supressor
- .25 Get a .25/.30 Supressor
Get it?
-
Sold out!
SC-40 ONLY not a full kit
Eaglevision Side-Cam SPLITTER ONLY
$134.00Select optionsPlease note:
This is the main body only, you cannot use this part alone without a scope connection method like the USH-46 (Collet system) or the 2B-USH/2B-UCH (Two Bar and Clamp System)
-
For G1, G2/22, G2/25, G30, SL22, SL25 or SL30
Gauntlet Tactical Conversion Kit
$139.99Select optionsIntroducing a Buck Rail and Hajimoto Collaboration! A super strong tactical conversion kit for the Umarex Gauntlet!
- Laser Sintered Nylon construction. LIFETIME WARRANTY
- Made in the USA by a veteran-owned business
- Add an AR Pistol Grip and Adjustable Buttstock to your Gauntlet
- Compatible with Gauntlet G1, G2, and SL30
- Accepts Milspec or Commercial AR15/AR308 Extension Tubes
- Handguard accepts M Lok accessories
- Over 1 pound of weight savings over OEM stock
Installation video is listed below
-
Ninja X Reg Custom Output Regulator up to 3100psi
Ninja High Pressure 5/8″-18UNF Custom Output Regulator
$144.95Select options5/8″-18UNF thread can be used on 3000PSI bottle as well. This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.
We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.
You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.
This is a direct replacement for the regulator found on the Gauntlets G1, G2 and G30 Caliber
Take advantage of a quality regulator for your high pressure application. MADE IN THE USA! Ninja HP regulator output pressures in increments of 100PSI. Simply select your desired output pressure from 1100PSI TO 3100PSI All custom built pressure units will have a +/- 50 psi tolerance.
-
NEW MODEL
Pro V3 for 3K and 4.5K Cylinders
Ninja Pro V3 Regulator 5/8″ Thread
$148.00Select optionsThe All New Hajimoto Pro V3 in 5/8”-18UNF Thread with Stainless Steel Cap Threads
Ninja's Pro V3 with rotional bonnet. A perfect replacement for the regulator found on the on the Gauntlet 2. A complete regulator rebuild kit is included! MADE IN THE USA! Ninja regulator output pressures in increments of 100PSI. Simply select your desired output pressure. Output ranges from 1100PSI to 2400PSI. All custom built pressure units will have a +/- 50 psi tolerance.
-
5/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
$149.00 – $159.00Select optionsNewly redesigned unit
Now has a high pressure and low pressure burst discs!
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800PSI adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF
The Ninja Flex regulator is available in any 900PSI spread to a maximum of 3100PSI output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex RegFlex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/700 to 1500PSIFlex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1600 to 2400PSIFlex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSIComes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
-
Sumo 1.6 x 6.25 inches
$150.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Ninja High Pressure Metric M18 Custom Output
$154.95 – $155.00Select optionsThe Hajimoto M18*1.5 Thread can be used on 3000PSI bottles as well. Ninja Paintball is beginning to produce these with a polished brass bonnet. We will be forced to switch over to these polished brass version once all the black steel bonnets are gone.
This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.
We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.
You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.
Take advantage of a quality regulator for your high pressure application. MADE IN THE USA! Ninja HP Metric regulator output pressures in increments of 100PSI. This is a M18 threaded regulator made for M18 threaded bottles. This will not fit Umarex Gauntlet Bottles which are 5/8"-18 Threaded. Simply select your desired output pressure from 1100PSI TO 3100PSI All custom built pressure units will have a +/- 75 psi tolerance. If you need a low output build with a fixed out of of something between 300 psi and 1100 psi, the CUSTOM pessure option and provide the output desired in the notes. If you are looking for a direct replacement for you Gauntlet2 .22, .25 & .30 You will want the 5/8"-18 Version that is found HERE
-
NEW MODEL
PRO V3 REG WITH 13CI TANK
Ninja 13ci 3000PSI Air Tank with Pro V3 Regulator
$155.00Select optionsIncludes Hajimotos Pro V3 regulator with Stainless Steel Threaded rotional Cap. Say goodbye to gauges and foster nipples not lining up with the stock openings when the is installed tight. A complete regulator rebuild kit is included!
This is an aluminum 13ci bottle that holds 3000PSI including a Pro V3 regulator with custom output pressures in increments of 100PSI. Simply select the desired pressure in the dropdown. Pressure Recommendations For Umarex Gauntlet Generation 1 .177, .22 and .25 Stock Gauntlet Gen1 .177/.22 | 13ci/3000/1100PSI Regulator Gauntlet with STK Installed .177/.22 | 13ci/3000/1400PSI Regulator Stock Gauntlet Gen1 .25 | 13ci/3000/1900PSI Regulator Gauntlet with STK Installed .25 | 13ci/3000/2100 Regulator
-
Flex Reg on 13ci Aluminum 3K
Gauntlet Flex Reg with 13ci Tank – Hajimoto Configurations
$169.00Select optionsIntroducing a Hajimoto Productions Exclusive offer!
13ci/213cc/.21L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 13 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSIFlex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1600 to 2400PSIInstalls on the Gauntlet with minor tank shroud modifications.
A 13ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg with typical G1/2-14 threads connects to your Umarex Gauntlet 1 or Gauntlet 2 without any modifications!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 13 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.