Uncategorized

Sale!
$75.00 – $93.00
Gauntlet STK
Super Tune Kit (STK) for Gauntlet 1 and 2
Rated 5.00 out of 5
$75.00 – $93.00
THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)

For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

CONTENTS:
- Adjuster Plug Assembly.
- Smaller, Lighter Composite Poppet.
- Hajimoto Hammer Spring (Black Long)
- Lighter Trigger Spring (Bright Small).
- 5/64″ Allen Wrench For Adjusting Power.
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.

Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:

Written Detailed Tuning Instructions for the STK

More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there.
Select options
$79.00 – $99.00
FX No Limit Scope Rings 1″, 30mm and 34mm
$79.00 – $99.00

FX shows that they are able to innovate not just within airguns themselves, but in other areas of the shooting sports. The FX No Limit scope rings are perfect for long-range shooting as you can vertically adjust and angle your mounts so you can always find the sweet spot on your scope. These rings are also very useful if you need to have your scope higher off the receiver to allow for oversized magazines or scope camera setups.

You will want these rings if you are planning on using my Expanded Magazine.

Select options
$99.00
Tanto 1.22 x 5 inches
Tanto 1.22 x 5 inches
$99.00

THIS IS AN AIRGUN ONLY PART

This part is designed and manufactured by DonnyFL

Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

Select options
Sale!
$115.00 – $424.00
With or Without Cylinder
Doux Avenger Bottle Adapter
$115.00 – $424.00
Convert your Air Venturi Avenger into a bottle PCP!
- Adapter Threaded for M18 x 1.5 Air Cylinder.
- Option to add a 500cc or 700cc 4.5K Carbon Fiber Bottle.
- All Stainless Steel Construction.
Made in South Africa

Installation video below:
Select options
$120.00
DonnyFL FX Suppressor
FX/DonnyFL 1.36 x 5 inches
$120.00

THIS IS AN AIRGUN ONLY PART

This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.

Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

Select options
Sale!
$125.00 – $130.00
Chronograph by Nate
NateChrony V2
$125.00 – $130.00

The NateChrony is a barrel mounted ballistic chronograph for all Air Rifles. It is accurate, affordable, super easy to use, and best of all – no more missed readings! The NateChrony mounts onto your barrel with one of the adapters for perfect alignment every time.
Using your mobile phone as the screen and battery, means you get the best display on the market and never get surprised by a flat battery in your Chronograph.

The NateChrony is fully featured and will provide all the data even the most demanding tuner requires. It displays a current shot string, and has four additional save slots – all of which retain the data when power is lost. You can configure pellet weight, display hold time, and adjust the NateChrony readings to match another Chronograph.

Specifications

Accuracy: calibrated to be within 1fps of actual pellet speed at 1,000fps from a certified set of master chronographs
Resolution: <0.1fps shot to shot at 1,000fps
Air powered guns only
CO2 power can cause vapour, not recommended
Maximum caliber: ~45-50 cal (depending on power)
Maximum power: 150 fpe

Select options
$130.00
Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
Rated 5.00 out of 5
$130.00

THIS IS AN AIRGUN ONLY PART

This part is designed and manufactured by DonnyFL

Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

Select options
$130.00 – $215.00
for .177, .22 and .25 NOT .30
Gauntlet Short Shroud Combo
$130.00 – $215.00
This part is designed and manufactured by DonnyFL for airgun use only

Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber

Stock baffle spring must be used!
Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.

If Your Gauntlet is:
- .177 Get a .177/.22 Supressor
- .22 Get a .22/.25 Supressor
- .25 Get a .25/.30 Supressor
Get it?
Select options
Sold out!
$134.00
SC-40 ONLY not a full kit
Eaglevision Side-Cam SPLITTER ONLY
$134.00

Please note:

This is the main body only, you cannot use this part alone without a scope connection method like the USH-46 (Collet system) or the 2B-USH/2B-UCH (Two Bar and Clamp System)

Select options
Sale!
$135.00 – $140.00
360CC 4.5K PSI M18 Threaded CF Tank
0.36L M18 Thread Carbon Fiber Tank
$135.00 – $140.00
Features
- Lightweight High Pressure Carbon fiber Cylinder
- 360cc/0.36L capacity
- Available in Gloss Or Matte
- 9″ x 2.4″ (228mm x 61.5mm)
- M18 Threaded
Shown Below On the HajiNotos
Select options
$139.99
For G1, G2/22, G2/25, G30, SL22, SL25 or SL30
Gauntlet Tactical Conversion Kit
Rated 5.00 out of 5
$139.99
Introducing a Buck Rail and Hajimoto Collaboration! A super strong tactical conversion kit for the Umarex Gauntlet!

If you would rather use the Gauntlet Tactical Builder Interface, click HERE
- Laser Sintered Nylon construction. LIFETIME WARRANTY
- Made in the USA by a veteran-owned business
- Add an AR Pistol Grip and Adjustable Buttstock to your Gauntlet
- Compatible with Gauntlet G1, G2, and SL30
- Accepts Milspec or Commercial AR15/AR308 Extension Tubes
- Handguard accepts M Lok accessories
- Over 1 pound of weight savings over OEM stock
Accessory options include a Grip, Buffertube, and Collapsable Butt Stock

Installation video is listed below
Select options
$144.95
Ninja X Reg Custom Output Regulator up to 3100psi
Ninja High Pressure 5/8″-18UNF Custom Output Regulator
$144.95
5/8″-18UNF thread can be used on 3000PSI bottle as well. This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.

We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve. The only function of this pin/ball is to allow the tank to retain air if it is off of the PCP. This is a paintball thing and should not be used in in HPA.

You should never try to unscrew a high-pressure output paintball-style regulator while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle. Read more in the following article https://hajimotoproductions.com/index.php/2024/11/11/regulator-thread-damage/

This is a direct replacement for the regulator found on the Gauntlets G1, G2 and G30 Caliber
```
Take advantage of a quality regulator for your high pressure application.

MADE IN THE USA!
Ninja HP regulator output pressures in increments of 100PSI.
Simply select your desired output pressure from 1100PSI TO 3100PSI
All custom built pressure units will have a +/- 50 psi tolerance.
```
Select options