Moderators/Suppressor/Adapters

Suppressors, Silencers, and Adapters.

Suppressors, Silencers, and Adapters.

Suppressors, Silencers, and Adapters.

  • $12.00

    for .177, .22 and .25 NOT .30

    Umarex Gauntlet Aluminum Air Stripper
    $12.00

    This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.

    Part does not fit Gauntlet .30 caliber

    This part is designed and manufactured by DonnyFL

    Select options
  • $14.00 – $18.00

    Adapter for NateChrony V2

    NateChrony Variable Adapter
    $14.00 – $18.00

    A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
    The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.

    Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.

    The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.

    Thumb screws are aluminium & supplied with either knurled or printed tabs.

    Price is for 1 adapter, with 1 set of screws.

    Select options
  • $20.00
    HP Baffle Stack For Umarex Gauntlet
    $20.00

    Part fits either the original Gauntlet or the Gauntlet 2

    THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.

    Select options
  • Barra 1100z Stak Pak W/Spring
    $27.00

    5 Piece Stak Pak W/Spring

    Barra 1100z Stak Pak W/Spring
    $27.00

    Only fits the 19.25″ barrel length version. Middle to late 2023 produced 1100Z barrels were increased in length to 22.25″ eliminating the free space that used to allow a spring and baffles to fit.
    Help quiet down your Barra 1100z with our custom-fit HP 5-piece Baffle Stak and tension spring. There are two different-sized baffles to help eliminate patterned harmonics in the air stream.

     

     

    Select options
  • HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
    $28.00
    HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
    $28.00

    Part fits either the original Gauntlet or the Gauntlet 2

    You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.

    Air Stripper comes with o-ring and silicone grease for installation.

    Select options
  • Sold out!
    $35.00
    Evanix Rainstorm II Baffle Stack
    $35.00

    Evanix Rainstorm II Baffle Stack

    Here is an 8 piece multi-sized baffle stack for the Evanix Rainstorm/Rainstorm II. The HP Baffle Stack strips away turbulent air and sound from the shot signature of the Umarex Gauntlet. The baffles trap sound and air in each cavity and force it to stay in the moderator chamber away from the pellet path.
    The Rainstorm HP Baffle Stack requires the non cone STAND OFF to be sized by the user. You will need to sand the STAND OFF down to the required height for your rifle.
    The HP Baffle Stack should be installed as follows, from the front, further-est from the barrel, Short/Full/Full/Short/Short/Full/Full/Standoff at the muzzle.

    Baffles should be pointing towards the breech

    <= Towards the breech —— Towards the Muzzle of shroud =>

    [░░] <░] <░░] <░░] <░] <░] <░░] <░░] CAP
    SO    SC     NC     NC    SC   SC    NC     NC

    SO = STAND OFF
    NC = NORMAL CONE
    SC = SHORT CONE

    Select options
  • Sold out!
    Artemis PP750 1/2 x 20 #A68
    $35.00
    Artemis PP750 1/2 x 20 #A68
    $35.00

    Fits the Artemis PP750 PCP

    This part is designed and manufactured by DonnyFL

    Read more
  • Sale!
    HP Stak Pak for Hatsan QE
    Original price was: $39.99.Current price is: $35.00.
    HP Stak Pak for Hatsan QE
    Original price was: $39.99.Current price is: $35.00.

    Stak Pak for Hatsan QE shrouds (.357 & .457 Not Included)

    Simply unscrew your shroud end cap, remove the two felt-covered stock baffle assemblies, remove the two aluminum stand-off chambers, and install the Hajimoto Stak Pak. No tools, no modifications, just a simple one-for-one swap! Some model Hatsans will use all the baffles others will need one less full-sized baffle, be sure to use both shorter baffles and leave out the full-sized one. If you need to leave one out, leave out the very first full-sized baffle and then arrange the stack as shown in the packaging.

    A ten-piece kit that directly replaces the two hair curler style baffles that come inside any Hatsan that has a QE shroud system, excluding .357 & .457 models. The bundle has nine baffle chambers to help remove both noise and turbulence in the air stream. The baffle stack rides on a high tension compression spring allowing for a perfect fit for any Hatsan QE PCP, excluding .357 & .457 models.

    The end result is a more laminar air stream which reduces projectile instability and substantially changes the sound of the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A24 adapter.

    Installation video is listed in the DESCRIPTION section below

     

    Select options
  • RTI Priest 2 Shroud Extender #A66
    $35.00

    RTI Priest 2 Shroud Extender #A66

    RTI Priest 2 Shroud Extender #A66
    $35.00

    If your Priest shroud sits behind the air bottle and you would like to use a larger suppressor, this extender will allow you to do so.

    Features:

    • 6061 T6 aluminum
    • Knurled cap
    • Matte black anodize
    Select options
  • Sold out!
    $35.00
    DonnyFL KOI/Tanto Endcaps
    $35.00

    KOI and Tanto End caps in 1/2 x 20 threads

    Select options
  • $35.00

    Replacement end caps

    Emperor/Ronin End Caps
    $35.00

    THIS IS AN AIRGUN ONLY PART

    Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.

    Select options
  • Sale!
    BUCK-RAIL 1/2 X 20 SUPPRESSOR
    $35.00 – $40.00

    Buck Rail Suppressor

    BUCK-RAIL 1/2 X 20 SUPPRESSOR
    $35.00 – $40.00

    Genuine Buck-Rail Product

    • Designed to be compatible with 1/2-20 UNF male threads
    • Stocked in 177/22 caliber
    • 3d printed in Polycarbonate plastic in the US by a veteran-owned business
    • Utilizes high quality EZ Lok steel inserts for extra durable threads
    • 7 cone-shaped interior baffle design with large muzzle exit expansion chamber
    • Dramatically reduces the report without diminishing accuracy or muzzle velocity
    Select options
  • Umarex Gauntlet 1/2 x 20 adapter #A23
    $40.00

    For the Gauntlet 1 or 2

    Umarex Gauntlet 1/2 x 20 adapter #A23
    $40.00

    This part is designed and manufactured by DonnyFL

    Select options
  • Sold out!
    Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
    $40.00
    Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
    $40.00

    Fits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s

    This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.

    If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.

    This part is designed and manufactured by DonnyFL

    Read more
  • Hatsan Bullmaster/Galatian with 1/2 x 20 UNF and thread adapter #A35
    $40.00
    Hatsan Bullmaster/Galatian with 1/2 x 20 UNF and thread adapter #A35
    $40.00

    Please note that when you add a suppressor to this gun, it does not properly index the magazine. If you plan to single load and use a suppressor that’ll be fine. I would also recommend using a suppressor one caliber size up to reduce the chance of pellet clipping.

    Select options
  • Hatsan Blitz M18X1 Adapter A117
    $40.00
    Hatsan Blitz M18X1 Adapter A117
    $40.00

    This part is designed and manufactured by DonnyFL

    This adapter allows you to screw on an airgun suppressor with M18x1 threads.

    Select options
  • $40.00

    1/2 x 20 UNF Adapter for Akela/Kratos

    Benjamin Akela/Kratos 1/2 x 20 Adapter A8
    $40.00

    Fits the Benjamin Akela and Kratos PCP’s

    This part is designed and manufactured by DonnyFL

    Select options
  • Sold out!
    HP Strip Stak Pak for Akela/Kratos
    $40.00

    Akela/Kratos Strip Stak Pak

    HP Strip Stak Pak for Akela/Kratos
    $40.00

    INCLUDES NEW ENHANCED AIR STRIPPER DESIGN

    Strip Stak Pak for the Benjamin Akela and Kratos PCP’s
    A nine-piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides variable-sized baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A8 adapter.
    The Air Stripper is threaded and comes with an o-ring and silicone grease for installation. The stock barrel shroud spring must be reused.     

    Replacement Air Stripper 0-ring is 14mm x 1.5mm

     

    Read more
  • Benjamin 1/2 x 20 adapter #A7
    $40.00

    Marauder, Armada and Fortitude

    Benjamin 1/2 x 20 adapter #A7
    $40.00

    This part is designed and manufactured by DonnyFL

    Select options
  • $40.00

    Hammer Adapter

    Umarex Hammer M18x1 Shroud Adapter A60
    $40.00

    This adapter replaces the factory shroud baffle and has M18x1 threads. Comes with thread protector

    This adapter does not fit on the Umarex Hammer Carbine.

    Select options
  • Umarex Gauntlet Strip Stak Pak (Bundle)
    $45.00

    for .177, .22 and .25 NOT .30

    Umarex Gauntlet Strip Stak Pak (Bundle)
    $45.00

    Hajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
    An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

    BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
    Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.

    Air Stripper comes with o-ring and silicone grease for installation.

     

     

    Select options
  • $45.00
    Hatsan QE 1/2 x 20 adapter #A24
    $45.00

    This part is designed and manufactured by DonnyFL

    Select options
  • Air Venturi Avenger Extender 1/2 x 20 Adapter #A70
    $45.00
    Air Venturi Avenger Extender 1/2 x 20 Adapter #A70
    $45.00

    Specifically for the AV Avenger

    Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.

    This part is designed and manufactured by DonnyFL

    Select options
  • HP Strip Stak Pak for PP750
    $45.00
    HP Strip Stak Pak for PP750
    $45.00

    Strip Stak Pak for the Artemis PP750
    A five (5) piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.
    Air Stripper comes with o-ring and silicone grease for installation.  Not available for Canada

    Select options
  • Umarex Origin 1/2 x 20 Adapter #A70
    $45.00
    Umarex Origin 1/2 x 20 Adapter #A70
    $45.00

    Specifically for the Umarex Origin

    Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.

    This version allows you to use a larger suppressor than the Tanto or KOI. Designed to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.

    This part is designed and manufactured by DonnyFL

    Select options
  • Beeman Underlever 1357 | 1358 Adapter #A86
    $45.00
    Beeman Underlever 1357 | 1358 Adapter #A86
    $45.00

    Specifically for the Beeman 1357 / 1358

    This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o’ring and put it on the new adapter.

    This part is designed and manufactured by DonnyFL

    Select options
  • $45.00
    Hatsan QE Big Bore .357/.457 M18x1 Adapter A54 #A54
    $45.00

    This part is designed and manufactured by DonnyFL

    Select options
  • HP Strip Stak Pak for Avenger
    $47.00

    Air Stripper, Tension Spring and Baffle Stack

    HP Strip Stak Pak for Avenger
    $47.00

    UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

    Strip Stak Pak for the Avenger

    A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
    Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

    Replacement Air Stripper 0-ring is 14mm x 1.5mm

    Select options
  • HP Strip Stak Pak for Origin
    $47.00

    Origin .22/.25

    HP Strip Stak Pak for Origin
    $47.00

    NEW ENHANCED DESIGN

    UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

    Strip Stak Pak for the Umarex Origin
    A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
    Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.

    Replacement Air Stripper 0-ring is 14mm x 1.5mm

    Select options
  • JTS Airacuda Adapter #A115
    $50.00

    DonnyFL A115 JTS Adapter

    JTS Airacuda Adapter #A115
    $50.00

    Specifically for the Airacuda Standard or the Max in any Caliber (.22, .25, or .30)

    Because this adapter was made to fit both the Standard and Max versions of the AiraCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not affect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design with this flexibility to overcome the challenges of this airgun’s shroud design so that moderators could be used.

    Key Features:

    • Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants.
    • Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel.

    This part is designed and manufactured by DonnyFL

    Select options
  • Sold out!
    $60.00
    DISCONTINUED
    HP Strip Stak Pak for Evanix Air Speed
    $60.00

    Evanix Air Speed Air Stripper and Baffle Stack _
    An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. Air stripper come with o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

    Replacement Air Stripper 0-ring is 14mm x 1.5mm

     

    Select options
  • $60.00

    for .177, .22 and .25 NOT .30

    Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter
    $60.00

    Part fits Umarex Gauntlet 177, .22 or .25. Not compatible with the Gauntlet .30 Caliber.

    This part is designed and manufactured by DonnyFL

    Select options
  • Emperor/Ronin Extender
    $60.00

    V3 6.26 inch Extension

    Emperor/Ronin Extender
    $60.00

    THIS IS AN AIRGUN ONLY PART

     

    Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it’s the latest model.

    Select options
  • $99.00

    Tanto 1.22 x 5 inches

    Tanto 1.22 x 5 inches
    $99.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL

    Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

    The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

    Select options
  • FX/DonnyFL 1.36 x 5 inches
    $120.00

    DonnyFL FX Suppressor

    FX/DonnyFL 1.36 x 5 inches
    $120.00

    THIS IS AN AIRGUN ONLY PART

    This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.

    Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

    The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

    Select options
  • Sale!
    NateChrony V2
    $125.00 – $130.00

    Chronograph by Nate

    NateChrony V2
    $125.00 – $130.00

    The NateChrony is a barrel mounted ballistic chronograph for all Air Rifles. It is accurate, affordable, super easy to use, and best of all – no more missed readings! The NateChrony mounts onto your barrel with one of the adapters for perfect alignment every time.
    Using your mobile phone as the screen and battery, means you get the best display on the market and never get surprised by a flat battery in your Chronograph.

    The NateChrony is fully featured and will provide all the data even the most demanding tuner requires. It displays a current shot string, and has four additional save slots – all of which retain the data when power is lost. You can configure pellet weight, display hold time, and adjust the NateChrony readings to match another Chronograph.

    Specifications

    Accuracy: calibrated to be within 1fps of actual pellet speed at 1,000fps from a certified set of master chronographs
    Resolution: <0.1fps shot to shot at 1,000fps
    Air powered guns only
    CO2 power can cause vapour, not recommended
    Maximum caliber: ~45-50 cal (depending on power)
    Maximum power: 150 fpe

    Select options
  • Tatsu 1.6 x 4.25 inches
    $130.00

    Tatsu 1.6 x 4.25 inches

    Tatsu 1.6 x 4.25 inches
    $130.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL

    Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

    The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

    Select options
  • Gauntlet Short Shroud Combo
    $130.00 – $215.00

    for .177, .22 and .25 NOT .30

    Gauntlet Short Shroud Combo
    $130.00 – $215.00

    This part is designed and manufactured by DonnyFL for airgun use only

    Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber

     

    Stock baffle spring must be used!
    Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.

    If Your Gauntlet is:

    • .177 Get a .177/.22 Supressor
    • .22 Get a .22/.25 Supressor
    • .25 Get a .25/.30 Supressor

    Get it?

    Select options
  • $150.00
    Sumo 1.6 x 6.25 inches
    $150.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL

    Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

    The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

    Select options
  • Sold out!
    Fat Boy 2 x 4.25 inches
    $175.00

    2 x 4.25 inches Fatboy 2.0

    Fat Boy 2 x 4.25 inches
    $175.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL

    2 x 4.25 inches Fatboy 2.0

    Take the width of the Ronan or Emperor and the length of the Tatsu then mix in some super cool modularity components and you end up with the Fat Boy. In the 2.0 version, we gave this Campbell soup can a face lift. New outer shell design along with interchangeable calibers from .177 up to .30. Shooters who wanted something short yet effective, the Fatboy will surprise you.

    Features:

    • Compatible with .177 to .30 calibers 
    • Includes 3 interchangeable air strippers
    • Redesigned 1/2 x 20 rear cap for easy gripping
    • Can be used with the 6.25 inch extender for more hush power
    • Measure 4.25 inches long by 2 inches in diameter
    • Weighs only 6.7 oz
    Read more
  • Shogun 1.6 x 8 inches
    $185.00
    Shogun 1.6 x 8 inches
    $185.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL

    Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

    Select options
  • Ronin 2 x 6.25 inch
    $185.00
    Ronin 2 x 6.25 inch
    $185.00

    THIS IS AN AIRGUN ONLY PART

    This part is designed and manufactured by DonnyFL out of high-quality 6061 Aluminum.

    The Ronin is made to quiet the big dogs. The Ronin is best on a high power .25 caliber or a Gauntlet .30 Caliber.

    We only stock the .22/.25 , .25/.30 caliber, and .357 in 1/2 x 20 UNF threaded versions.

    If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
    The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
    The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
    The .357 is for shrouded barrel .30 calibers or direct barrel threaded .357 caliber PCPs

    If you are looking to make the Ronin or Emperor really quiet, consider the 6.25″ Ronin extension chamber for extra stealthiness.

    Select options
  • $239.99

    DonnyFL EMPEROR V3 Moderator

    Emperor 2 x 11 inch
    $239.99

    THIS IS AN AIRGUN ONLY PART

     

    Introducing the largest DonnyFL suppressor catered to the big bore guns.

    Overall length 11 inches and weighs in at 1 lb.

    This thing is built like a tank to tame those power hungry shooters.

    Select options

Copyright All rights reserved Hajimoto Productions LLC 2024

Proudly powered by WordPress . Theme: multipurpose shop by eDataStyle.