Suppressors, Silencers, and Adapters.
-
$12.00for .177, .22 and .25 NOT .30
Umarex Gauntlet Aluminum Air Stripper
$12.00Select options
This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.
Part does not fit Gauntlet .30 caliber
This part is designed and manufactured by DonnyFL
-
$20.00HP Baffle Stack For Umarex Gauntlet
$20.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.
-
$27.005 Piece Stak Pak W/Spring
Barra 1100z Stak Pak W/Spring
$27.00Select options
Only fits the 19.25″ barrel length version. Middle to late 2023 produced 1100Z barrels were increased in length to 22.25″ eliminating the free space that used to allow a spring and baffles to fit.
Help quiet down your Barra 1100z with our custom-fit HP 5-piece Baffle Stak and tension spring. There are two different-sized baffles to help eliminate patterned harmonics in the air stream.
-
$28.00HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
$28.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.
Air Stripper comes with o-ring and silicone grease for installation.
-
Sold out!
$35.00Evanix Rainstorm II Baffle Stack
$35.00Select optionsEvanix Rainstorm II Baffle Stack
Here is an 8 piece multi-sized baffle stack for the Evanix Rainstorm/Rainstorm II. The HP Baffle Stack strips away turbulent air and sound from the shot signature of the Umarex Gauntlet. The baffles trap sound and air in each cavity and force it to stay in the moderator chamber away from the pellet path.
The Rainstorm HP Baffle Stack requires the non cone STAND OFF to be sized by the user. You will need to sand the STAND OFF down to the required height for your rifle.
The HP Baffle Stack should be installed as follows, from the front, further-est from the barrel, Short/Full/Full/Short/Short/Full/Full/Standoff at the muzzle.Baffles should be pointing towards the breech
<= Towards the breech —— Towards the Muzzle of shroud =>
[░░] <░] <░░] <░░] <░] <░] <░░] <░░] CAP
SO SC NC NC SC SC NC NCSO = STAND OFF
NC = NORMAL CONE
SC = SHORT CONE -
Sold out!
$35.00Artemis PP750 1/2 x 20 #A68
$35.00Read moreFits the Artemis PP750 PCP
This part is designed and manufactured by DonnyFL
-
Sale!
Original price was: $39.99.$35.00Current price is: $35.00.HP Stak Pak for Hatsan QE
Original price was: $39.99.$35.00Current price is: $35.00.Select optionsStak Pak for Hatsan QE shrouds (.357 & .457 Not Included)
Simply unscrew your shroud end cap, remove the two felt-covered stock baffle assemblies, remove the two aluminum stand-off chambers, and install the Hajimoto Stak Pak. No tools, no modifications, just a simple one-for-one swap! Some model Hatsans will use all the baffles others will need one less full-sized baffle, be sure to use both shorter baffles and leave out the full-sized one. If you need to leave one out, leave out the very first full-sized baffle and then arrange the stack as shown in the packaging.
A ten-piece kit that directly replaces the two hair curler style baffles that come inside any Hatsan that has a QE shroud system, excluding .357 & .457 models. The bundle has nine baffle chambers to help remove both noise and turbulence in the air stream. The baffle stack rides on a high tension compression spring allowing for a perfect fit for any Hatsan QE PCP, excluding .357 & .457 models.
The end result is a more laminar air stream which reduces projectile instability and substantially changes the sound of the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A24 adapter.
Installation video is listed in the DESCRIPTION section below
-
$35.00RTI Priest 2 Shroud Extender #A66
RTI Priest 2 Shroud Extender #A66
$35.00Select optionsIf your Priest shroud sits behind the air bottle and you would like to use a larger suppressor, this extender will allow you to do so.
Features:
- 6061 T6 aluminum
- Knurled cap
- Matte black anodize
-
Sold out!
$35.00DonnyFL KOI/Tanto Endcaps
$35.00Select optionsKOI and Tanto End caps in 1/2 x 20 threads
-
$35.00Replacement end caps
Emperor/Ronin End Caps
$35.00Select optionsTHIS IS AN AIRGUN ONLY PART
Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.
-
$40.00For the Gauntlet 1 or 2
Umarex Gauntlet 1/2 x 20 adapter #A23
$40.00Select optionsThis part is designed and manufactured by DonnyFL
-
$40.00Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
$40.00Select optionsFits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s
This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.
If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.
This part is designed and manufactured by DonnyFL
-
$40.00Hatsan Bullmaster/Galatian with 1/2 x 20 UNF and thread adapter #A35
$40.00Select optionsPlease note that when you add a suppressor to this gun, it does not properly index the magazine. If you plan to single load and use a suppressor that’ll be fine. I would also recommend using a suppressor one caliber size up to reduce the chance of pellet clipping.
-
Sold out!
$40.00Hatsan Blitz 1/2 x 20 adapter #A84
$40.00Read moreThis part is designed and manufactured by DonnyFL
-
$40.001/2 x 20 UNF Adapter for Akela/Kratos
Benjamin Akela/Kratos 1/2 x 20 Adapter A8
$40.00Select optionsFits the Benjamin Akela and Kratos PCP’s
This part is designed and manufactured by DonnyFL
-
$40.00Akela/Kratos Strip Stak Pak
HP Strip Stak Pak for Akela/Kratos
$40.00Select optionsINCLUDES NEW ENHANCED AIR STRIPPER DESIGN
Strip Stak Pak for the Benjamin Akela and Kratos PCP’s
A nine-piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides variable-sized baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A8 adapter.
The Air Stripper is threaded and comes with an o-ring and silicone grease for installation. The stock barrel shroud spring must be reused.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
$40.00
Marauder, Armada and Fortitude
Benjamin 1/2 x 20 adapter #A7
$40.00Select optionsThis part is designed and manufactured by DonnyFL
-
$40.00Hammer Adapter
Umarex Hammer M18x1 Shroud Adapter A60
$40.00Select optionsThis adapter replaces the factory shroud baffle and has M18x1 threads. Comes with thread protector
This adapter does not fit on the Umarex Hammer Carbine.
-
$45.00for .177, .22 and .25 NOT .30
Umarex Gauntlet Strip Stak Pak (Bundle)
$45.00Select optionsHajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.
Air Stripper comes with o-ring and silicone grease for installation.
-
$45.00Hatsan QE 1/2 x 20 adapter #A24
$45.00Select optionsThis part is designed and manufactured by DonnyFL
-
Sold out!
$45.00Air Venturi Avenger Extender 1/2 x 20 Adapter #A70
$45.00Read moreSpecifically for the AV Avenger
Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.
This part is designed and manufactured by DonnyFL
-
$45.00HP Strip Stak Pak for PP750
$45.00Select optionsStrip Stak Pak for the Artemis PP750
A five (5) piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.
Air Stripper comes with o-ring and silicone grease for installation. Not available for Canada
-
$45.00Umarex Origin 1/2 x 20 Adapter #A70
$45.00Select optionsSpecifically for the Umarex Origin
Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.
This version allows you to use a larger suppressor than the Tanto or KOI. Designed to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.
This part is designed and manufactured by DonnyFL
-
$45.00Beeman Underlever 1357 | 1358 Adapter #A86
$45.00Select optionsSpecifically for the Beeman 1357 / 1358
This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o’ring and put it on the new adapter.
This part is designed and manufactured by DonnyFL
