Accessories

$47.00
Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00

UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Avenger

A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$47.00
Origin .22/.25
HP Strip Stak Pak for Origin
Rated 4.33 out of 5
$47.00

NEW ENHANCED DESIGN

UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$48.00 – $96.00
Two Bar System or Extra Clamps
Eaglevision Twobar or Clamps (Scope Cam)
$48.00 – $96.00
These parts are for you if:
- You already have an Eaglevision Scope Camera System and want to convert it to the new Two Bar Configuration
- You need additional clamps to eliminate the need to constantly swap a clamp to another scope.
This is high quality 30mm to 25mm (1″) or 34mm to 30mm scope tube adaptors, made of aluminum.

Here is a top-quality installation video from AirBuks.

Be sure to go by his YouTube channel and watch some of his awesome air gunning content.

Designed To Work With All Eaglevision Scope Mounts.
Select options
$49.00
Needed to install a bottle
Avenger Bull Pup Primary Adapter
$49.00

Here is our primary adapter that allows the installation of the Doux Tech on the Avenger Bull Pup PCP.
The primary adapter replaces the lower pressure tube adapter allowing the bottle adapter to be installed on the airgun.

You will transfer the o-ring from the Avengers pressure tube to the Primary Adapter.

Select options
$50.00
Eaglevison Firefly Camera Carrier
Firefly 8SE to Eaglevision Scope Cam
$50.00

For the user that has an Eaglevision Scope Cam Setup and would like to use a FireFly with it. Some images show the camera case with the optional open door installed. This is not an included option.

Select options
$50.00
DonnyFL A115 JTS Adapter
JTS Airacuda Adapter #A115
$50.00
Specifically for the Airacuda Standard or the Max in any Caliber (.22, .25, or .30)

Because this adapter was made to fit both the Standard and Max versions of the AiraCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not affect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design with this flexibility to overcome the challenges of this airgun’s shroud design so that moderators could be used.

Key Features:
- Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants.
- Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel.
This part is designed and manufactured by DonnyFL
Select options
$50.00
For G30, G30SL or Any Gen Gauntlet
Gauntlet Barrel Chambering Correction
$50.00

Service to correct the Gauntlet series of PCP’s. Calibers include .177, .22, 25, 30, or the 30SL, hard chambering of slugs issues.

Select options
$50.00
For all G barrels in all calibers
G Barrel Transfer Port Work
$50.00

Service to improve the barrels transfer port by enlarging and polishing the inlet. All calibers benefit from this service when trying to achieve maximum power and efficiency from your build.

Select options
$55.00
Trigger work
$55.00

The service can be added to an existing tune/build or a stand-alone ship in service. If you are shipping me your trigger group, you simply decock and degas the Gauntlet, remove it from the stock, and remove the two fasteners that hold the group to the bottom of the pressure tube.

If you elect the stand-alone ship service, shipping instructions will follow which detail the packaging and address to ship to.

Select options
$55.00
11.4cc plenum expansion for Avenger
Doux – Avenger Power Plenum
$55.00
AVENGER/LEVIATHAN POWER PLENUM:
- SIZE: 11.4cc
- STACKABLE
- BLACK ANODIZED WITH MATT BLACK GUN COATING
- TYPICAL PERFORMANCE INCREASE IS AROUND 20FT/S WITH NO OTHER MODIFICATIONS.
THIS PLENUM IS NOT DESIGNED TO NOT FIT THE BULL PUP VERSION

INSTALLATION CAN BE MADE USING TYPICAL SNAP RING PLIERS

MADE IN SOUTH AFRICA

Installation video below
Select options
$59.95 – $69.95
Microbore 4500PSI Extension
Ninja Microbore Fill Whip
$59.95 – $69.95
- 30% Lighter and Smaller than standard HPA hoses
- Extremely flexible 30 or 46 inch hose
- 4500 PSI working pressure
- Works with any HPA or CO2 system
- Made in USA
Select options
$59.99
Side Shot Scope Clamps
$59.99

The clamps come in 1″, 30mm and 34mm to fit your scope tube. They allow you to mount have multiple clamps already installed on your rifles so all you need to do is slide on the Side-Shot, tighten the thumbscrews and record!

These parts are 100% American-made, precision CNC’d parts! These clamps are precision machined, sent in to be anodized, and then back for assembly.

Solid, Secure and its stainless steel parts keep it from rusting.

Select options
$59.99
Clamp with Pic rail
Saber Tactical 55mm Clamp
$59.99

If you’re uneasy about drilling into your factory gun stock, this 52mm bottle clamp will easily attach to your 52mm carbon fiber or aluminum bottles. It has rubber pads on the inside to prevent any marring to your bottle.

Fits perfectly for Umarex Gauntlets Stock tanks.

This clamp has picatinny rails at the bottom for you to connect your preferred picatinny accessories.

Select options
Sold out!
$60.00
DISCONTINUED
HP Strip Stak Pak for Evanix Air Speed
$60.00

Evanix Air Speed Air Stripper and Baffle Stack _
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. Air stripper come with o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$60.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter
Rated 5.00 out of 5
$60.00

Part fits Umarex Gauntlet 177, .22 or .25. Not compatible with the Gauntlet .30 Caliber.

This part is designed and manufactured by DonnyFL

Select options
$60.00
GOPRO Camera Housing
Eaglevision GOPRO Camera Housing
$60.00
EV GoPro Camera Housings.
- Camera Case model for GoPro 5-6-7
- Camera Case for 9-10-11-12
Select options
$65.00
Gauntlet Regulator Tester
$65.00

Assembled and tested by Hajimoto using quality US Parts! Don’t guess what the output of your Gauntlets regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.

Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like these shown

Select options
Sale!
Original price was: $82.00.Current price is: $68.00.
Collet system goes over diopter
Eaglevision USH-46 Collet
Original price was: $82.00.Current price is: $68.00.

The USH-46 is designed to hold all the scopes with or without threads on eye relief and will connect to the Eaglevision scope camera mounting system.

This unit can be connected to 99% of the scopes with a dimension of 40mm to 46.5mm and it will find the center automatically while you are tightening it.

Select options
$70.00
Install Super Tune Kit
$70.00

Please note that these are services to your rifle and not just the parts. If your looking for parts only head to the PRODUCTS section of the website.

The service of installing the Super Tune Kit does not include shipping. Return shipping will be calculated and added at check out. Shipping cost will be based on a complete rifle sent to Hajimoto Productions in the original box and packing materials. Stock modification is part of the STK install which is why you need to send the entire rifle to us not just the action. If the rifle is received in something heavier than the typical 14lbs, additional shipping costs will need to be paid prior to the rifle being shipped back to the customer.

Select options
Sale!
$75.00 – $85.00
Gauntlet STK
Super Tune Kit (STK) for Gauntlet 1 and 2
Rated 5.00 out of 5
$75.00 – $85.00
THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)

For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

CONTENTS:
- Adjuster Plug Assembly.
- Smaller, Lighter Composite Poppet.
- Hajimoto Hammer Spring (Black Long)
- Lighter Trigger Spring (Bright Small).
- 5/64″ Allen Wrench For Adjusting Power.
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.

Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:

Written Detailed Tuning Instructions for the STK

More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there.
Select options
Sold out!
Original price was: $130.00.Current price is: $85.00.
AE Swede
Avenger Tactical Chassis V3
Original price was: $130.00.Current price is: $85.00.

It is heavier made and over all much better with improved fitment and looks. Each chassis is 3D resin printed in house and then threads are finished with taps, bead blasted and then painted flat black with oil based enamel paint.

The V3 Chassis has greatly reduced flex and is overall much more solid than the previous versions. This chassis is not too tall like other 3D printed chassis and so the airgun does not turn into a sail or become tippy because of the added height. The side walls have been thickened over 5mm over the V1 chassis and is much more robust. It features improved styling and fitment via extra time spent in development. There is not void in the space behind the trigger group which was a weak spot on the previous V1 chassis.

Read more
Sold out!
$88.00 – $325.00
Allows for a dual Reg Setup
AE Swede Avenger Bottle Adapter
$88.00 – $325.00

This is AE Swede’s bottle adapter and plug that allows the user to run dual regulators.
Here is where you will find the reg you need. Just select 3000PSI output.

Select options
Sold out!
$99.00
Eaglevision INS Mount
Infinity INS Elevation Adjustable Scope Mount 30mm Ring Picatinny
$99.00
Eaglevision has designed and developed an amazing scope mount that allows the scope to move vertically along a guided path. The mount is lockable in different positions using two screws. This mount can be used as a low profile or be adjusted to the high profile too if your scope objective is too close to your rifle barrel or shroud. These mounts resolve a lot of problems for shooters who like to shoot long range and often run out of adjustment clicks on their turrets.

The mount can also come in handy if you have not been able to use your favorite scope due to lack of space between the rings or the odd position of your dovetail or Picatinny rail on your gun. We are very proud of this product as it became a “must-have” for people who love their bullpups.
The best application of this mount however is for people who want to reach out further than their ordinary mounts allow them to. By keeping the front mount at its lowest and elevating the rear mount to the highest point you can zero in your gun far beyond your normal mounts allows you to, without using the clicks on your turrets hence keeping the optical center of your scope intact (the ideal situation for long-range shooting).

Another great feature is these mounts allow the scope to be lifted to allow for large or expanded magazines.

Item includes:
- 2 x infinity scope mount.
- 2 x allen key (different sizes).
- 4 x spears screws.
- 1 x large spear screw.
- Protection ring fabric.
- Waterproof case.
Read more
$99.00
Eaglevision IPS Mount
Infinity IPS Elevation Adj Scope Mount 30mm Ring Picatinny TopRail
$99.00
Eaglevision has designed and developed an amazing scope mount that allows the scope to move vertically along a guided path. The mount is lockable in different positions using two screws. This mount version has a section of rail on top for the mounting of a flashlight or camera or anythingThis mount can be used as a low profile or be adjusted to the high profile too if your scope objective is too close to your rifle barrel or shroud. These mounts resolve a lot of problems for shooters who like to shoot long range and often run out of adjustment clicks on their turrets.

The mount can also come in handy if you have not been able to use your favorite scope due to lack of space between the rings or the odd position of your dovetail or Picatinny rail on your gun. We are very proud of this product as it became a “must-have” for people who love their bullpups.
The best application of this mount however is for people who want to reach out further than their ordinary mounts allow them to. By keeping the front mount at its lowest and elevating the rear mount to the highest point you can zero in your gun far beyond your normal mounts allows you to, without using the clicks on your turrets hence keeping the optical center of your scope intact (the ideal situation for long-range shooting).

Another great feature is these mounts allow the scope to be lifted to allow for large or expanded magazines.

Item includes:
- 2 x infinity scope mount.
- 2 x allen key (different sizes).
- 4 x spare screws.
- 1 x large spear screw.
- Protection ring fabric.
- Waterproof case.
Select options

EV GoPro Camera Housings.