Umarex 6K Gauge

Related products

• 

  $47.00

  Air Stripper, Tension Spring and Baffle Stack

  HP Strip Stak Pak for Avenger

  $47.00

  UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

  Strip Stak Pak for the Avenger

  A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
  Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

  Replacement Air Stripper 0-ring is 14mm x 1.5mm

  

  Select options This product has multiple variants. The options may be chosen on the product page
• Sale!

  

  $75.00 – $93.00Price range: $75.00 through $93.00

  Gauntlet STK

  Super Tune Kit (STK) for Gauntlet 1,2, OR LIMITED

  Rated 5.00 out of 5

  $75.00 – $93.00Price range: $75.00 through $93.00

  THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
  IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

  Kits available to fit Gauntlet 1, Gauntlet 2, Gauntlet 2 SL, or Gauntlet 2 Limited 22/25, variants.

  The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment, opening the possibility of higher or lower foot-pounds (FPE) for whatever the user desires. Do you need only 5FPE? No problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

  Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required to know the rate of travel of the projectile. (Power examples given are the .22 caliber version Gauntlet 1) 

  For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation, as there is a difference, and improperly selected kits are not returnable.
  BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

  CONTENTS:

  • Adjuster Plug Assembly.
  • Smaller, Lighter Composite Poppet.
  • Hajimoto Hammer Spring (Black Long)
  • Lighter Trigger Spring (Bright Small).
  • 5/64″ Allen Wrench For Adjusting Power.

  Be sure to follow my written instructions in the document below.
  Use the video to install but follow these written instructions to adjust and tune the STK:

  Written Detailed Tuning Instructions for the STK

  More details below.
  Always read the content below because any revised instructions, video, photos, or other links will be there.

  Select options This product has multiple variants. The options may be chosen on the product page

• 

  $35.00 – $40.00Price range: $35.00 through $40.00

  For Gauntlet .177, .22, .25 and .30 Calibers

  Hajimoto’s Gauntlet Expanded Magazine

  Rated 4.00 out of 5

  $35.00 – $40.00Price range: $35.00 through $40.00

  Now offering two designs. The original NO LOD and the new magnetic removable HP 2.0 design allows for much faster loading.

  Here is a high-quality, high-capacity magazine designed to fit the Umarex Gauntlet 1 or 2 in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjustable rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.

  The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell

  Features

  • An easy to load NO LID design or the new magnetic lidded version.
  • No pre-winding is necessary.
  • Easy partial fill design.
  • .177 – 21 shots which is an increase of 110% more shots over the stock magazine!
  • .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
  • .25 = 15 shots which is an increase of 37.5% more shots over the stock magazine!
  • .30 = 11 shots which is an increase of 57.5% more shots over the stock magazine!
  • The magazine height for the .177, .22 and .25 is 50.25MM (1.978″)
  • The magazine height for the .30 is 46.20MM (1.820″) Max Slug/Pellet length supported 11.20mm (0.441″)

  WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE

  Select options This product has multiple variants. The options may be chosen on the product page