Additional information
| Weight | 32 oz |
|---|---|
| Dimensions | 14 × 2 × 2 in |
Barrel Service Notos
$110.00
Notos Barrel Service
This is what we do to our Haji-Notos Custom Builds. but you can have the same service performed on your Notos barrel as well. The Transfer port work increases the port and polishes the opening to allow greater airflow to produce more power more efficiently.
You ship us your Notos Barrel and we execute the following:
- Remove the fixed molded plastic suppressor (the suppressor is destroyed in the process).
- Increase and polish the barrel transfer port.
- Two new barrel o-rings are provided.
- Clean up and polish the barrel crown.
- 1/2 x 20 UNF Threaded Adapter Included.
- Barrel Shroud End Cap and Barrel Guide Included.
- Thoroughly clean and silicone barrel bore.
Notos Barrel Removal
Your Barrel is very easily removed by removing the 2.5mm button head screw on top of the Picatinny rail near the magazine opening. Once the 2.5mm screw is removed, there is a 2mm set screw below it that holds the barrel into the receiver block. Loosen the 2mm screw four revolutions and slide out the barrel.
Shipping
When you place the order for the above-described service, we will send you an order processing notification with a copy of your invoice. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your barrel for modification.
You must be logged in to post a review.
Related products
-
$130.00Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
$130.00Select options This product has multiple variants. The options may be chosen on the product pageTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
$28.00HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
$28.00Select options This product has multiple variants. The options may be chosen on the product pagePart fits either the original Gauntlet or the Gauntlet 2
You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.
Air Stripper comes with o-ring and silicone grease for installation.
-
Price range: $299.00 through $310.005/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
Price range: $299.00 through $310.00Select options This product has multiple variants. The options may be chosen on the product page
NOTE: THE NINJA FLEX REGULATOR HAS A LIMITED INVENTORY
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800 – 1000 psi adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF (Bottle Thread) and Typical Paintball Threads of .825-14 NGO (PCP Thread).
Please note the Flex regulator can be used with any Air, Co2, or Nitrogen driven air gun not just the Gauntlet, providing it has the correct threading.
The Ninja Flex regulator is available in any 900 psi spread to a maximum of 3100 psi output. For the Gauntlet, select the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be. Please note that the highest output the Flex Regulator can be configured for is 3100 PSI, but we can build it to any number below that. Example, a user wants the maximum output of their Flex regulator to be 2800, we will build the regulator so that the adjustable range of that build is 1800 to 2800PSI.How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex RegFlex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/600 to 1500PSIFlex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1500 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1500 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1500 to 2400PSIFlex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSIComes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Reviews
There are no reviews yet.