NateChrony SmartTarget
$40.00
Accessories
The NateChrony SmartTarget has 6 outputs – 1 for addressable LEDs, and 5 programmable outputs. These accessories connect to these outputs to indicate hit detection, shot placement, and can drive external equipment via relay boards.
Short Range LED Kit – Cross
The short range kit features 5 LEDs in a cross shape, with spacing of 50mm. This makes it convenient and compact for shorter ranges, typically 50-100m. It connects directly to the SmartTarget outputs via a supplied 1m cable.
The middle LED will show green on a center hit, red on the outer LEDs when struck at the outer edges, and orange on the outer LEDs when struck between the center and outer edges.
The cross can be mounted to a surface behind the target (to avoid spalling) via tape, bands or zip ties.
Long Range LED Kit – 4+2 LEDs
The long range kit features 4 LED modules (and 2 spare), which are connected to either the 4-connector board or can be daisy-chained to each other, via the supplied 30cm cables and connectors. This allows spacing between LEDs of up to 60cm, ideal for easy recognition at long ranges.
All four LEDs will display green on a center hit, show red when struck at the outer edge, and orange when struck between the center and outer edge.
The LEDs are supplied with quality 3M double sided tape, and are stuck to the rear surface of the target, or another surface behind the target face.
Long Range LED Kit – 10+2 LEDs
This kit is the same style as the 4+2 above, but with more LEDs and larger 10x connector board. This allows for larger and creative designs, with different LED colours and behaviours, such as a doe or buck with highlighted antlers and eyes.
DIY LED Kit – 10+2 LEDs
The ultimate in flexibility – we provide the LED boards and snap connector blocks, you then wire and connect them in any style you want. This is perfect for target makers or people that want to do customise their targets, and really transform a boring target into a fully interactive one.
LEDs will need wires soldered to the boards, however the supplied snap connectors make interconnecting and LED replacements quick and easy. You will also need to mount them using tape, or they can be drilled and screwed into place.
Informational videos below.
Sold out!
Related products
-
Price range: $11.00 through $20.00For G1 G2 & G30 Variants
Umarex Gauntlet Tune O-ring Kit
Price range: $11.00 through $20.00Select optionsHajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
-
$47.00Origin .22/.25
HP Strip Stak Pak for Origin
$47.00Select optionsNEW ENHANCED DESIGN
UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
Sold out!
$110.00Fits the G1, G2/G2SL or G30/G30SL
Real 2 Stage Trigger for the Gauntlet
$110.00Read moreFull-fledged 2-stage trigger for the Umarex Gauntlet 1, 2, G30, bolt or sidelever variants. This trigger is a direct replacement for the single-stage trigger that ships with the Umarex Gauntlet. This trigger is a straightforward install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
- The Trigger Is Stainless Steel 17-4 Through Hardened
- The Trigger Shoe Is Aluminum 6061-T6
Please see the installation video below for more details.
Super Tune Kit Users
You must use the stock trigger return spring with the two-stage trigger as the trigger spring that comes with the Super Tune Kit is too light to be effective with the two-stage trigger.
Reviews
There are no reviews yet.