Adapter for NateChrony V2
Price range: $14.00 through $18.00
A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.
Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.
The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.
Thumb screws are aluminum & supplied with either knurled or printed tabs.
Price is for 1 adapter, with 1 set of screws.
Additional information
| Weight | 6 oz |
|---|---|
| Dimensions | 6.25 × 3.25 × 2 in |
| Size | 35mm-15mm (S), 45mm-15mm (L) |
You must be logged in to post a review.
Related products
-
Price range: $13.00 through $22.00For G1 G2 & G30 Variants
Umarex Gauntlet Tune O-ring Kit
Price range: $13.00 through $22.00Select options This product has multiple variants. The options may be chosen on the product pageHajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
-
Price range: $15.00 through $70.00Bipod and Picatinny Rail
Price range: $15.00 through $70.00Select options This product has multiple variants. The options may be chosen on the product page
Installation Video for 1.5″ Picatinny rail on the Umarex Gauntlet forearm.
-
$130.00Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
$130.00Select options This product has multiple variants. The options may be chosen on the product pageTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Reviews
There are no reviews yet.