GP10-13 Case and Adapter for OrionCam2
Price range: $60.00 through $230.00
This kit provides any GoPro 10 thru 13 Black owner, everything they need to allow the GP10-13 Black to be used as the capture device for their existing OrionCam2 Scope cam!
A user can also purchase this kit without a lens kit if they already have a modified GoPro.
In the full kit, you receive the Eaglevision Lens Kit, a Custom Camera Case for the GoPro 1 through 13 Black, and a Special GP10-13 to OrionCam2 Adapter.
Below is a photo of this kit installed and displayed on our HajiNoto PCP
Lens fits the GoPro 10 thru 13 black.
GoPro 10 thru 13 cannot be used on the scope cam without changing the lens.
In order to use this product as intended, you MUST watch the below video on how to change the lens.
Once the lens has been removed, it can’t be reused again, and your camera can be used only with our lens.
Your camera will be out of warranty if you remove the lens.
DO NOT order the Eaglevision scope cam kit or this lens if you are not confident you can execute the installation.
The GoPro retention plate and the Eaglevision finish plate use Torx T4 star head screws. You will need a T4 screwdriver or T4 screwdriver bit to do the installation.
This is a high-quality GoPro customized low sensor lens with a special coating and a large wide lens to get maximum light to GoPro camera when using Gopro on rifle scopes, when using it for scope cam such as air gunning, airsoft, paintball, hunting, etc.
We are not responsible for any damage you may cause to your camera when doing the lens swap.
Lens swap video
Additional information
| Weight | 2 oz |
|---|---|
| Dimensions | 3 × 3.5 × 1.25 in |
| OPTIONS | WITH LENS, WITHOUT LENS, CASE ONLY |
You must be logged in to post a review.
Related products
-
$47.00Origin .22/.25
HP Strip Stak Pak for Origin
$47.00Select options This product has multiple variants. The options may be chosen on the product pageNEW ENHANCED DESIGN
UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
Price range: $13.00 through $22.00For G1 G2 & G30 Variants
Umarex Gauntlet Tune O-ring Kit
Price range: $13.00 through $22.00Select options This product has multiple variants. The options may be chosen on the product pageHajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
-
$50.00Reg Pressure Tester
HubenPower Regulator Tester
$50.00Select options
High quality HubenPower reg tester.
Features
- Micro threaded activation knob.
- Built in quick action pressure relief knob.
- High pressure gauge to 6000 psi.
Don’t guess what the output of your regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.
Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like those shown below.
Reviews
There are no reviews yet.