EagleVision 1/1.8″ 12MM LENS
$160.00
Lens fits the GoPro 9, 10, 11,12 and 13.
GoPro 9, 10, 11, 12, and 13 cannot be used on the scope cam without changing the lens.
In order to use this product as intended, you MUST watch the below video on how to change the lens.
Once the lens has been removed, it can’t be reused again, and your camera can be used only with our lens.
Your camera will be out of warranty if you remove the lens.
DO NOT order the Eaglevision scope cam kit or this lens if you are not confident you can execute the installation.
The Gopro retention plate and the Eaglevision finish plate use Torx T4 star head screws. T4 screwdriver included.
This is a high-quality GoPro customized low sensor lens with a special coating and a large wide lens to get maximum light to GoPro camera when using Gopro on rifle scopes, when using it for scope cam such as air gunning, airsoft, paintball, hunting, etc.
We are not responsible for any damage you may cause to your camera when doing the lens swap.
Lens swap video
[youtube https://www.youtube.com/watch?v=kyO6ENcNhb4]
6 in stock
Additional information
| Weight | 2 oz |
|---|---|
| Dimensions | 3 × 3.5 × 1.25 in |
You must be logged in to post a review.
Related products
-
$70.00Install Super Tune Kit
$70.00Select optionsPlease note that these are services to your rifle and not just the parts. If your looking for parts only head to the PRODUCTS section of the website.
The service of installing the Super Tune Kit does not include shipping. Return shipping will be calculated and added at check out. Shipping cost will be based on a complete rifle sent to Hajimoto Productions in the original box and packing materials. Stock modification is part of the STK install which is why you need to send the entire rifle to us not just the action. If the rifle is received in something heavier than the typical 14lbs, additional shipping costs will need to be paid prior to the rifle being shipped back to the customer.
-
Sold out!
$47.00Origin .22/.25
HP Strip Stak Pak for Origin
$47.00Select options This product has multiple variants. The options may be chosen on the product pageNEW ENHANCED DESIGN
UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
$350.00Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
$350.00Select options This product has multiple variants. The options may be chosen on the product pageIntroducing a Hajimoto Productions Exclusive offer!
22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSIFlex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSIIf you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE
Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
Reviews
There are no reviews yet.