Eaglevision USH-46 Collet

Related products

• 

  $15.00 – $26.00Price range: $15.00 through $26.00

  For G1 G2 & G30 Variants

  Umarex Gauntlet Tune O-ring Kit -NO-RING

  $15.00 – $26.00Price range: $15.00 through $26.00

  Hajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2

  Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.

  

  I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.

  Some of the NO-Ring seals have the leading edge precision ground.
  

  These tapered / precision ground types need to be installed as shown below

  

  (Images are of the .30 caliber NO RING)

  You get:

  • 2  of pellet probe NO-ring seals.
  • 2 sets of barrel o-rings.
  • 2 sets of tank block o-rings.
  • 2  of valve body o-rings.

  

  

   

  Select options This product has multiple variants. The options may be chosen on the product page

• 

  $47.00

  Origin .22/.25

  HP Strip Stak Pak for Origin

  Rated 4.33 out of 5

  $47.00

  NEW ENHANCED DESIGN

  UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

  Strip Stak Pak for the Umarex Origin
  A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
  Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.

  Replacement Air Stripper 0-ring is 14mm x 1.5mm

  Select options This product has multiple variants. The options may be chosen on the product page

• 

  $35.00 – $40.00Price range: $35.00 through $40.00

  For Gauntlet .177, .22, .25 and .30 Calibers

  Hajimoto’s Gauntlet Expanded Magazine

  Rated 4.00 out of 5

  $35.00 – $40.00Price range: $35.00 through $40.00

  Now offering two designs. The original NO LOD and the new magnetic removable HP 2.0 design allows for much faster loading.

  Here is a high-quality, high-capacity magazine designed to fit the Umarex Gauntlet 1 or 2 in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjustable rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.

  The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell

  Features

  • An easy to load NO LID design or the new magnetic lidded version.
  • No pre-winding is necessary.
  • Easy partial fill design.
  • .177 – 21 shots which is an increase of 110% more shots over the stock magazine!
  • .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
  • .25 = 15 shots which is an increase of 37.5% more shots over the stock magazine!
  • .30 = 11 shots which is an increase of 57.5% more shots over the stock magazine!
  • The magazine height for the .177, .22 and .25 is 50.25MM (1.978″)
  • The magazine height for the .30 is 46.20MM (1.820″) Max Slug/Pellet length supported 11.20mm (0.441″)

  WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE

  Select options This product has multiple variants. The options may be chosen on the product page