$110.00
Full-fledged 2-stage trigger for the Umarex Gauntlet 1, 2 or G30. This trigger is a direct replacement for the single-stage trigger that ships with the Umarex Gauntlet. This trigger is a straightforward install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
Please see the installation video below for more details.
Super Tune Kit Users
You must use the stock trigger return spring with the two-stage trigger as the trigger spring that comes with the Super Tune Kit is too light to be effective with the two-stage trigger.
9 in stock
Full-fledged 2 stage trigger for the Umarex G1, G2 or G30. This is a direct replacement for the single stage trigger that ships with the Umarex Gauntlet.
This is a very easy install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
You must be logged in to post a review.
Includes G1, G2, G30, G2SL, & G30SL variants
Available in the classic Picatinny rail version or the 15mm thick rail less version.
Versions for Gauntlet 1, Gauntlet 2, Gauntlet 30 as well as the SL Versions!
Evanix Rainstorm II Baffle Stack
Here is an 8 piece multi-sized baffle stack for the Evanix Rainstorm/Rainstorm II. The HP Baffle Stack strips away turbulent air and sound from the shot signature of the Umarex Gauntlet. The baffles trap sound and air in each cavity and force it to stay in the moderator chamber away from the pellet path.
The Rainstorm HP Baffle Stack requires the non cone STAND OFF to be sized by the user. You will need to sand the STAND OFF down to the required height for your rifle.
The HP Baffle Stack should be installed as follows, from the front, further-est from the barrel, Short/Full/Full/Short/Short/Full/Full/Standoff at the muzzle.
Baffles should be pointing towards the breech
<= Towards the breech —— Towards the Muzzle of shroud =>
[░░] <░] <░░] <░░] <░] <░] <░░] <░░] CAP
SO SC NC NC SC SC NC NC
SO = STAND OFF
NC = NORMAL CONE
SC = SHORT CONE
Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Introducing a Hajimoto Productions Exclusive offer!
22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSI
Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSI
If you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE
Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
danhibben (verified owner) –
Fantastic upgrade to the G30
I had adjusted my stock trigger as finely as possible but this unit with its polished face is amazing
Improved my accuracy at long rang dramatically
Definitely worth the money
Mark Dale (verified owner) –
Great upgrade from the stock trigger, put one in both my Gauntlet 2 .25 & my .30 and it’s a night and day difference.
Thanks for another Great product Hajimoto !!!
Steve Horch (verified owner) –
This trigger is amazing. Best upgrade you can do to your Gauntlet. Really happy with this in my G2 .25