Adapter for NateChrony V2
$14.00 – $18.00
A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.
Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.
The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.
Thumb screws are aluminium & supplied with either knurled or printed tabs.
Price is for 1 adapter, with 1 set of screws.
Additional information
| Weight | 6 oz |
|---|---|
| Dimensions | 6.25 × 3.25 × 2 in |
| Size | 35mm-15mm, 45mm-15mm |
You must be logged in to post a review.
Related products
-
$47.00Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00Select optionsUPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
$65.00Gauntlet Regulator Tester
$65.00Select optionsAssembled and tested by Hajimoto using quality US Parts! Don’t guess what the output of your Gauntlets regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.
Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like these shown
-
$159.00 – $169.005/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
$159.00 – $169.00Select options
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800 – 900 psi adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF (Bottle Thread) and Typical Paintball Threads of .825-14 NGO (PCP Thread).
Please note the Flex regulator can be used with any Air, Co2, or Nitrogen driven air gun not just the Gauntlet, providing it has the correct threading.
The Ninja Flex regulator is available in any 900 psi spread to a maximum of 3100 psi output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex RegFlex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/600 to 1500PSIFlex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1500 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1500 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1500 to 2400PSIFlex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSIComes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Reviews
There are no reviews yet.