Description
Air Stripper, Tension Spring and Baffle Stack
$47.00
UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
You must be logged in to post a review.
Related products
-
$45.00Air Venturi Avenger Extender 1/2 x 20 Adapter #A70
$45.00Select optionsSpecifically for the AV Avenger
Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.
This part is designed and manufactured by DonnyFL
-
Sold out!
$35.00Evanix Rainstorm II Baffle Stack
$35.00Select optionsEvanix Rainstorm II Baffle Stack
Here is an 8 piece multi-sized baffle stack for the Evanix Rainstorm/Rainstorm II. The HP Baffle Stack strips away turbulent air and sound from the shot signature of the Umarex Gauntlet. The baffles trap sound and air in each cavity and force it to stay in the moderator chamber away from the pellet path.
The Rainstorm HP Baffle Stack requires the non cone STAND OFF to be sized by the user. You will need to sand the STAND OFF down to the required height for your rifle.
The HP Baffle Stack should be installed as follows, from the front, further-est from the barrel, Short/Full/Full/Short/Short/Full/Full/Standoff at the muzzle.Baffles should be pointing towards the breech
<= Towards the breech —— Towards the Muzzle of shroud =>
[░░] <░] <░░] <░░] <░] <░] <░░] <░░] CAP
SO SC NC NC SC SC NC NCSO = STAND OFF
NC = NORMAL CONE
SC = SHORT CONE -
$150.00Sumo 1.6 x 6.25 inches
$150.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Reviews
There are no reviews yet.