Regulators & Tanks

All things high pressure. Regulators, tanks, and bottles.

$4.00
Ninja fill port o’ring
Fill Port O’ring Fits Ninja
$4.00

5 Dura 90 fill port o’rings that are a direct replacement for most Ninja Paintball regulators

Select options
$8.00
Tank to PCP O-rings (10 Pak)
$8.00

10 Polyurethane CO2 / HPA Tank O-Rings (90 Durometer) The color is completely dependent on availability which will be RED or WHITE/TRANSLUCENT

Select options
$9.95
Burst Disk Two Pack
Regulator Burst Disks 1.8k, 3k, 5k & 7.5k
$9.95
- 1.8k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 3k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 5k burst disk is used as the high-pressure burst disk on 3k tanks
- 7.5k burst disk is used as the high-pressure burst disk on 4.5k tanks
Actual burst disk finish may be Black, or Bright depending on availability.
Select options
Sold out!
$17.00
DISCONTINUED
Ninja Magna Cap Fill Nipple Cover – BLACK
$17.00

Patented Magnetic design Lightweight Aluminum Helps to keep the dirt out!

MADE IN THE USA!!!!

Read more
$18.50
Umarex Gauntlet Regulator Shim Pak
$18.50
Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet

I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.

The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
  (Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.

DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.

Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.

You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.

If you rapid fill, there is a good chance you will pop your burst disc.
Select options
$21.95
Ninja Regulator Rebuild Kit Part #NINJARBK
$21.95

Ninja Paintball Tank Regulator Replacement Part #NINJARBK – Rebuild Kit for Ninja NON Pro Regulators.

User selectable included burst disc rating (1.8K, 3K, 5K or 7.5K)

Select options
$21.95
Ninja PRO V2 Regulator Rebuild Kit Part #PRORBK
$21.95

Ninja Paintball Tank Regulator Replacement Part #PRORBK – This Rebuild Kit for Ninja Pro V2 Regulators ONLY.

Like the one below:

This rebuild kit is not for the Umarex Gauntlet Stock Regulator.

User selectable included burst disc rating (1.8K, 3K, 5K or 7.5K)

Select options
$21.95
3/4″ Black face 3000PSI gauge
3000PSI 1/8″ NPT Pressure Gauge
$21.95
- 1/8″ NPT THREAD
- 3000PSI DIAL MAX
Select options
$21.95
Mini 5000PSI face
Ninja Black Mini Gauge
$21.95

Ninja Paintballs mini pressure gauge.

Face is black and the dial reads to 5000PSI

Select options
$21.95
NINJAMFV
Ninja Mini Fill Valve
$21.95
Select options
$21.95
NINJAOFV
Ninja O-ring Boss Fill Valve
$21.95
Select options
$22.00
30mm Long Quick Connecter
Extended Fill Coupler
$22.00
- Safe for use on all pre-charged equipment with a max working pressure of 340BAR, 5000psi. Do not exceed maximum working pressure.
- This extended socket is designed to allow connection to “Foster Type” fill nipples that are recessed deeply within the stock.
- If you need a coupler release tool, then this socket should overcome that problem as the release collar is a full 30mm long, as opposed to the 10.5mm long on a standard quick release foster coupler.
- Suitable for FX deep recess stocks, Daystate and Brocock deep recess stocks.
- A great answer for the Hajimoto Productions Flex Regulator install on the Umarex Gauntlet as shown in the photos below.
Select options
$24.95
Flex reg white face gauge
Ninja 4K White Face Gauge
$24.95
- 1/8″ NPT THREAD
- 4000PSI DIAL MAX
Select options
$24.95 – $30.00
Ninja Paintball X Reg Rebuild Kit #NINJARBKX
$24.95 – $30.00

Ninja Paintball Tank Regulator Replacement Part #X_REG_RBLDKT – This Rebuild Kit for Ninja X Regulators ONLY.
Like the one below:

Other variants are for the Gauntlet 2 in .22 caliber, .25 caliber, and .30 caliber. Be sure to select the proper kit type. User selectable included burst disc rating (1.8K, 3K, 5K or 7.5K)

There is a Flex Reg option but it requires photos so we can be sure what variant you have.

Select options
$30.00
Oil Water Separator Cartiridge
$30.00

Replacement / Additional Filter element. This cartridge is for the PCP Air Compressor Filter 4500psi Oil Water Separator we offer. The cartridge has molecular sieve, activated carbon, felt absorbing pads, and dividers installed and ready to go.

Select options
$30.00
From 7/8″-14 to M18x1.5
Saber Tactical Tank Valve adapter
$30.00

This adapter allows you to convert the threads on our tank valve from 7/8-14 to M18x1.5. The M18x1.5 is common on carbon fiber gun tanks.

Select options
$45.00
Regulator Service or Pressure Change
Regulator Service or Pressure Change
$45.00

This is a service to repair, test, leak test, adjust or increase the output pressure of a Umarex Gauntlet 1 or 2, regulator to a customer’s requested output. The regulator will be tested and calibrated to within +/- 75 PSI. Parts such as Gauges, Burst discs, Bonnets, Pistons, Caps, or Regulator bodies are not included. If parts are determined to be required to repair the regulator, pricing will be determined, quoted, and will need to be paid prior to the return of the regulator.

Please note that if you have a Taiwan-produced regulator, which is the regulator that is located at the top of the photo, there are very limited corrections that can be made to these units and you may end up needing a new regulator. Please use the notes area to provide the Generation and caliber of the rifle. Also, give as much detail as possible of the issue or the requested pressure output and so forth.

Once the order is physically reviewed, you will receive a second notification with details associated with packaging and shipping the items in for service.

When you place the order for the above-described service, you will receive an order processing notification. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your regulator or regulator and tank assembly.

This service is not a hydro test of the tank/bottle and is focused only on the regulator’s functionality and visual inspection assemblies.

Please note that this service is not associated with any manufacturer’s warranty, so please be sure to exhaust all warranty options prior to sending us your regulator for service as our working on the part voids any manufacturer-provided warranties.

Select options
$55.00
11.4cc plenum expansion for Avenger
Doux – Avenger Power Plenum
$55.00
AVENGER/LEVIATHAN POWER PLENUM:
- SIZE: 11.4cc
- STACKABLE
- BLACK ANODIZED WITH MATT BLACK GUN COATING
- TYPICAL PERFORMANCE INCREASE IS AROUND 20FT/S WITH NO OTHER MODIFICATIONS.
THIS PLENUM IS NOT DESIGNED TO NOT FIT THE BULL PUP VERSION

INSTALLATION CAN BE MADE USING TYPICAL SNAP RING PLIERS

MADE IN SOUTH AFRICA

Installation video below
Select options
$59.95 – $69.95
Microbore 4500PSI Extension
Ninja Microbore Fill Whip
$59.95 – $69.95
- 30% Lighter and Smaller than standard HPA hoses
- Extremely flexible 30 or 46 inch hose
- 4500 PSI working pressure
- Works with any HPA or CO2 system
- Made in USA
Select options
$65.00
Gauntlet Regulator Tester
$65.00

Assembled and tested by Hajimoto using quality US Parts! Don’t guess what the output of your Gauntlets regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.

Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like these shown

Select options
$110.00 – $175.00
PCP Air Compressor Filter 4500psi Oil Water Separator
$110.00 – $175.00

A quality water, oil and odor filter system designed to protect your PCP’s! Consider selecting the combinations that come with the extra-length fill whip so you can stand your filter up and down and still have plenty of slack to connect to your PCP.

Whether you are using a hand pump or a personal compressor it is vitally important that only clean dry air be introduced in your air reservoir.

Made from high-quality aircraft aluminum and is rated for safe use.

Don’t make the mistake of not drying your air as it will destroy regulators as well as your aluminum pressure vessels.

Select options
Sale!
$115.00 – $424.00
With or Without Cylinder
Doux Avenger Bottle Adapter
$115.00 – $424.00
Convert your Air Venturi Avenger into a bottle PCP!
- Adapter Threaded for M18 x 1.5 Air Cylinder.
- Option to add a 500cc or 700cc 4.5K Carbon Fiber Bottle.
- All Stainless Steel Construction.
Made in South Africa

Installation video below:
Select options
$144.95
Ninja X Reg Custom Output Regulator up to 3100psi
Ninja High Pressure 5/8″-18UNF Custom Output Regulator
$144.95
5/8″-18UNF thread can be used on 3000PSI bottle as well. This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.

We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.

You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.

This is a direct replacement for the regulator found on the Gauntlets G1, G2 and G30 Caliber
```
Take advantage of a quality regulator for your high pressure application.

MADE IN THE USA!
Ninja HP regulator output pressures in increments of 100PSI.
Simply select your desired output pressure from 1100PSI TO 3100PSI
All custom built pressure units will have a +/- 50 psi tolerance.
```
Select options

$148.00

NEW MODEL

Pro V3 for 3K and 4.5K Cylinders

Ninja Pro V3 Regulator 5/8″ Thread

$148.00

The All New Hajimoto Pro V3 in 5/8”-18UNF Thread with Stainless Steel Cap Threads

Ninja's Pro V3 with rotional bonnet.
A perfect replacement for the regulator found on the on the Gauntlet 2.
A complete regulator rebuild kit is included!

MADE IN THE USA!
Ninja regulator output pressures in increments of 100PSI.
Simply select your desired output pressure.
Output ranges from 1100PSI to 2400PSI.
All custom built pressure units will have a +/- 50 psi tolerance.

Select options

$149.00 – $159.00
5/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
$149.00 – $159.00

Newly redesigned unit
Now has a high pressure and low pressure burst discs!

Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800PSI adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF

The Ninja Flex regulator is available in any 900PSI spread to a maximum of 3100PSI output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.

How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex Reg

Flex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/700 to 1500PSI

Flex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1600 to 2400PSI

Flex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1600 to 2400PSI

Flex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1600 to 2400PSI

Flex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSI

Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

Select options
$154.95 – $155.00
Ninja High Pressure Metric M18 Custom Output
$154.95 – $155.00
The Hajimoto M18*1.5 Thread can be used on 3000PSI bottles as well.

The Bonnet is Steel not aluminum for maximum strength and low wear.

This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.

We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.

You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.
```
Take advantage of a quality regulator for your high pressure application.

MADE IN THE USA!
Ninja HP Metric regulator output pressures in increments of 100PSI.
This is a M18 threaded regulator made for M18 threaded bottles.
This will not fit Umarex Gauntlet Bottles which are 5/8"-18 Threaded.
Simply select your desired output pressure from 1100PSI TO 3100PSI
All custom built pressure units will have a +/- 75 psi tolerance.

If you need a low output build with a fixed out of of something between 
300 psi and 1100 psi, the CUSTOM pessure option and provide the output
desired in the notes.

If you are looking for a direct replacement for you Gauntlet2 .22, .25 & .30
You will want the 5/8"-18 Version that is found HERE
```
Select options

Ninja 13ci 3000PSI Air Tank with Pro V3 Regulator

$155.00

NEW MODEL

PRO V3 REG WITH 13CI TANK

Ninja 13ci 3000PSI Air Tank with Pro V3 Regulator

$155.00

Includes Hajimotos Pro V3 regulator with Stainless Steel Threaded rotional Cap. 
Say goodbye to gauges and foster nipples not lining up with the stock openings when the is installed tight.
A complete regulator rebuild kit is included!

This is an aluminum 13ci bottle that holds 3000PSI including a Pro V3 regulator with custom output pressures in increments of 100PSI.
Simply select the desired pressure in the dropdown.

Pressure Recommendations For Umarex Gauntlet Generation 1 .177, .22 and .25
Stock Gauntlet Gen1 .177/.22 | 13ci/3000/1100PSI Regulator
Gauntlet with STK Installed .177/.22 | 13ci/3000/1400PSI Regulator
Stock Gauntlet Gen1 .25 | 13ci/3000/1900PSI Regulator
Gauntlet with STK Installed .25 | 13ci/3000/2100 Regulator

Select options

$169.00
Flex Reg on 13ci Aluminum 3K
Gauntlet Flex Reg with 13ci Tank – Hajimoto Configurations
$169.00

Introducing a Hajimoto Productions Exclusive offer!

13ci/213cc/.21L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!

Flex 13 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSI

Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1600 to 2400PSI

Installs on the Gauntlet with minor tank shroud modifications.

A 13ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg with typical G1/2-14 threads connects to your Umarex Gauntlet 1 or Gauntlet 2 without any modifications!

The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.

Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!

When installing the Flex 13 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.

Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.

Select options
$173.00 – $175.00
NEW MODEL
PRO V3 ON 22ci 3K Cylinder
Ninja 22ci 3000PSI Air Tank with Pro V3 Regulator
$173.00 – $175.00

Includes Ninja’s Pro V3 regulator with Stainless Steel Threaded 36o° rotational Cap.
Say goodbye to gauges and foster nipples not lining up with the openings in the stock.

This is an aluminum 22ci bottle that holds 3000PSI including a Pro V3 regulator with custom output pressures in increments of 100PSI. Simply select the desired pressure in the dropdown.

PRESSURE – STOCK AND RECOMMENDED
Stock .177/.22 | 22ci/3000/1100PSI Regulator
Super Tuned .177/.22 (IF STK IS INSTALLED) | 22ci/3000/1400PSI Regulator

Stock .25 | 22ci/3000/1900PSI Regulator
Super Tuned .25 (IF STK IS INSTALLED) | 22ci/3000/2100 Regulator

This setup is for the original Umarex Gauntlet 1 with the Black stock.
A complete regulator rebuild kit is included!

NINJA REGULATORS ARE MADE IN THE USA!

Select options
$195.00
Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
$195.00

Introducing a Hajimoto Productions Exclusive offer!

22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!

Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSI

Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSI

If you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE

Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.

A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!

The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.

Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!

When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.

Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.

Select options
$200.00
Tank Valve ST0031
Saber Tactical Tank Valve
$200.00

Replace your factory tank valve with our larger valve. The large knobs and handle make filling and releasing air a breeze

Select options
Sale!
Original price was: $260.00.Current price is: $220.00.
0.5L/500cc CE Certified CF Tank
0.50L Carbon Fiber Tank 4500PSI
Original price was: $260.00.Current price is: $220.00.

Half a liter of air, right here!

0.5L/500cc CE Certified CF Tank
Perfect fit for your custom build.

M18x1.5 Threaded

This is the same bottle we use on the TacVenger builds we offer.

Select options
$249.99 – $309.99
300cc, 580cc or 700cc Bottles
Air Marksman Carbon Fiber Tanks
$249.99 – $309.99
- M18x1.5 neck thread.
- 300cc (.3 Liter), 580cc (.58 Liter), or 700cc (.7 Liter)
- 300 bar fill pressure (4351 PSI)
- Bottle only no regulator or adapters included.
Select options
$274.00
4.5K PSI Ninja Reg on a 18ci/295cc/.29L CE Certified CF Tank
Ninja Reg on 18ci Carbon Fiber Bottle
$274.00

Direct replacement with no modifications required for the Umarex Gauntlet 2!
18ci/295cc/.29L 4500 PSI Carbon Fiber Bottle

Hajimoto is bringing sexy back! Doesn’t that carbon fiber look awesome on there!

Includes Ninja’s HP regulator.
The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This 4500 PSI carbon fiber bottle is 18ci and is absolutely gorgeous on the Gauntlet 1 or Gauntlet 2.

The Gauntlet 1 will need to have its tank shroud inside diameter increased to allow the foregrip/tank cover to side over this carbon fiber tank.

Operating Pressure Recommendations

Gauntlet 1:
.177/.22 Stock operating pressure 1100PSI Max Recommended pressure is 1400PSI.
.25 Caliber Stock operating pressure 1900PSI Max Recommended pressure is 2100PSI.

Gauntlet 2:
.22 Stock operating pressure 1900PSI Max Recommended pressure is 2100PSI.
.25 Caliber Stock operating pressure 2100PSI Max Recommended pressure is 2300PSI.

NINJA REGULATORS ARE MADE IN THE USA!

Select options
Sale!
Original price was: $390.00.Current price is: $280.00.
0.7L/700cc CE Certified CF Tank
0.70L Carbon Fiber Tank 4500PSI
Original price was: $390.00.Current price is: $280.00.

0.7L/700cc CE Certified CF Tank
Perfect fit for your custom build.

M18x1.5 Threaded

If you plan to use this bottle with a Gauntlet, you must remove and leave removed, the tank shroud. This bottle cannot use the flex reg as it is threaded M18.

Consider our barrel bands for the 500cc and 700cc bottles on the Gauntlet found HERE

Select options
$294.00
NEW MODEL
PRO V3 Reg on a 22.5ci/370cc/.37L CE Certified CF Tank
Ninja Pro V3 Reg on 22.5ci Carbon Fiber Bottle
$294.00

ALL NEW!

Direct replacement with no modifications required for the Umarex Gauntlet 2 and Gauntlet 30 Cal!
22.5ci/370cc/.37L CE Certified CF Tank
Shaves off 1/2 a pound of weight compared to the 4500psi stock aluminum tank.
A complete regulator rebuild kit is included!

Includes the New Hajimoto Pro V3 regulator with Stainless Steel rotational bonnet.
Say goodbye to gauges and foster nipples not lining up with the openings in the stock.

The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This 4500 PSI carbon fiber bottle is 22.5ci and is absolutely gorgeous on the Gauntlet series of PCP.

The Gauntlet 1 will need to have its tank shroud inside diameter increased slightly to allow the foregrip/tank cover to side over this carbon fiber tank or simply remove the tank shroud.

Operating Pressure Recommendations

Gauntlet 1:
.177/.22 Stock operating pressure 1100PSI Max Recommended pressure is 1400PSI.
.25 Caliber Stock operating pressure 1900PSI Max Recommended pressure is 2300PSI.

Gauntlet 2:
.22 Stock operating pressure 1900PSI Max Recommended pressure is 2150PSI.
.25 Caliber Stock operating pressure 2100PSI Max Recommended pressure is 2400PSI.

NINJA REGULATORS ARE MADE IN THE USA!

Select options
Sold out!
Original price was: $339.00.Current price is: $295.00.
Flex Reg on 18ci/295cc/.29L CE Certified CF Tank
Power Flex Combo 18.3ci Carbon Fiber 4500PSI
Original price was: $339.00.Current price is: $295.00.
Introducing a Hajimoto Productions Exclusive offering!
18ci/295cc/.29L CE Certified CF Tank

Fits the Gauntlet 2 without any modifications.

The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. An 18.3ci carbon fiber 4500PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet! The massive volume of air afforded you is mind-blowing.

The diameter of the tank is 54-55mm across so a modification to the forearm is required if you desire to continue to use the Gauntlets tank shroud. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

Gauntlet Bottle Shroud Mod

Please see the examples provided in the accompanying photos.

The Gauntlet 2 forearm slides right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom. Please be careful if you have accessories on any of the MLok openings as the screws or MLok fasteners may scratch the tank when the shroud is slid forward or back.

Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!.

The cylinder’s outside dimension is slightly larger than the stock aluminum tank so my standard HP Barrel Band does not fit. You will need to use the HP Barrel Band CFT version
```
Regulator is Made in the USA!
The Power Flex Combo is set to either of the two Gauntlet configurations.
Simply select the proper configuration.

Power Flex Combo Configuration For .177/.22 Cal
Flex Reg set to 700 to 1500PSI
```
```
Power Flex Combo Configuration For .25 Cal
Flex Reg set to 1600 to 2400PSI
```
```
DO NOT USE Power Flex Combo Configuration For .25 CONFIG on .177 or .22
they are not capable of handling the pressures.
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
```
Select options
$310.00 – $350.00
500cc CF Tank with Adjustable Reg
Flex Reg RTI Version & Tank
$310.00 – $350.00

Flex Reg designed and configured specifically for RTI PCP’S such as Prophet, Priest, & Priest 2
This Flex Reg comes paired with a brand-new Carbon fiber 4500PSI tank. The regulator is externally adjustable and has an effective adjustable range of 900PSI (62bar).

Using the slider you select what the maximum output will be and because the regulator has the ability to adjust, you can reduce that maximum output pressure down as much as 900PSI (62bar). You can of course set the pressure anywhere along that 900PSI (62bar) range to suit your tuning requirements. The regulator will not have a pin or ball seal in the bonnet. The tank cannot be removed while under pressure and must be degassed.

Because of practical limitations, regulator max output will be +/- 50PSI (3.5bar) within the requested maximum output.

Comes with a spanner wrench for adjusting the output on the fly.

** This regulator is 5/8″-18UNF threaded and will not fit M18 threaded bottles. This configured Reg is not sold separately.

Select options
Sale!
Original price was: $375.00.Current price is: $330.00.
Flex reg and 22.5ci/370cc/.37L CE Certified CF Tank
Power Flex Combo 22.5ci Carbon Fiber 4500PSI
Original price was: $375.00.Current price is: $330.00.

Introducing a Hajimoto Productions Exclusive offer!

22.5ci/370cc/.37L CE Certified CF Tank
Newly redesigned unit
Now has a high pressure and low pressure burst discs!

Installs on the Gauntlet 2 with minor tank shroud modifications, forearm slides right over the carbon fiber cylinder. Installation video at the bottom of the page.

The CF Tank is CE Certified and made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This included a 22.5ci carbon fiber 4500PSI cylinder with externally adjustable Ninja Flex Reg for your custom build including the Umarex Gauntlet 1 or Gauntlet 2! The massive volume of air in these 22.5ci tanks is mind-blowing!

The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

Please be careful if you have accessories on any of the M-Lok openings as the screws or MLok fasteners may protrude into the tank area and scratch the tank when the shroud is slid forward or back. We recommend that if you have any MLok accessories installed, you remove them when sliding the shroud on or off. We also recommend covering the brass inserts in the tank shroud with cloth tape to protect your carbon fiber finish.

The Gauntlet 2 forearm slides right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom. See photo below

Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!

When installing the Flex regulator on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.

Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

Because of practical limitations, regulator output will be +/- 75PSI to the requested output.

Select options
Sale!
$349.00 – $360.00
Flex reg and 30ci/500cc/.5L CE Certified CF Tank
Power Flex Combo 30ci/.5L Carbon Fiber 4500PSI
$349.00 – $360.00

Please note that this combo will not fit a Gauntlet or Gauntlet 2 as the tank diameter is larger than the rifle’s tank shroud will allow. This combo is intended for builds that do away with the tank shroud or to be used on other PCP’s that allow for a typical paintball regulator installation.

Introducing a Hajimoto Productions Exclusive offer!

30ci/500cc/.5L CE Certified CF Tank
Newly redesigned unit
Now has a high pressure and low pressure burst discs!

The CF Tank is CE Certified made to ISO 11119-3 standard. They have seamless aluminum alloy 6061 liner wound with high strength Japan-imported carbon fiber and glass fiber reinforced plastic full composite layers and subjected to an autofrettage pressure. This includes a 30ci/500cc/.5L CE Certified 4500PSI cylinder with externally adjustable Ninja Flex Reg for your custom build.

The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 900PSI!

Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

Because of practical limitations, regulator output will be +/- 75PSI (3.5bar) within the requested output.

Select options
Sale!
$360.00 – $419.00
Ninja High Pressure Metric M18 Custom Output with Carbon Fiber Tank
Ninja High Pressure Metric M18 Custom Output with Carbon Fiber Tank
$360.00 – $419.00

Awesome configurations if you don’t care if the Gauntlet bottle shroud stays off. The 700cc on the G30 is beast mode!!!

Ninja Paintball High Pressure Regulator mounted on a quality 0.5L (500cc) or 0.7L (700cc) a 4500PSI rated Carbon Fiber Cylinder.

We build the regulator to any custom output pressure in 100 PSI increments from 1100PSI to 3100PSI

All custom built pressure units will have a +/- 75 psi tolerance.

Select options
Sale!
Original price was: $460.00.Current price is: $419.00.
HP M18 Reg and 700cc/.7L CE Certified CF Tank
Power 700 Combo
Original price was: $460.00.Current price is: $419.00.

The Power 700 Combo is a 4500PSI Ninja High-Pressure M18 reg mounted on a 0.7L/700cc Carbon Fiber 4500PSI Cylinder.

The High-Pressure reg paired with the 700cc cylinder means shots galore!

Please note that this combo will not fit a Gauntlet or Gauntlet 2 as the tank diameter is larger than the rifle’s tank shroud will allow. This combo is intended for builds that do away with the tank shroud or to be used on other PCP’s that allow for a typical paintball regulator installation. Use the Notes if you are looking for a lower PSI than 2800PSI as we can build the reg to ANY PSI 3100PSI and lower.

Consider adding our Barrel Band made for the Power 700 Combo!

Because of practical limitations, regulator output will be +/- 75PSI (3.5bar) within the requested output.

Select options

BACK FROM RMAC

PLEASE BE PATIENT WITH US

AS WE GET CAUGHT UP