Moderators/Suppressor/Adapters - Hajimoto Productions LLC

$45.00
Umarex Origin 1/2 x 20 Adapter #A70
$45.00

Specifically for the Umarex Origin

Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.

This version allows you to use a larger suppressor than the Tanto or KOI. Designed to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.

This part is designed and manufactured by DonnyFL

Select options
$45.00
Beeman Underlever 1357 | 1358 Adapter #A86
$45.00

Specifically for the Beeman 1357 / 1358

This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o’ring and put it on the new adapter.

This part is designed and manufactured by DonnyFL

Select options
$45.00
Hatsan QE Big Bore .357/.457 M18x1 Adapter A54 #A54
$45.00

This part is designed and manufactured by DonnyFL

Select options
$47.00
Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00

UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Avenger

A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$47.00
Origin .22/.25
HP Strip Stak Pak for Origin
Rated 4.33 out of 5
$47.00

NEW ENHANCED DESIGN

UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$50.00
DonnyFL A115 JTS Adapter
JTS Airacuda Adapter #A115
$50.00
Specifically for the Airacuda Standard or the Max in any Caliber (.22, .25, or .30)

Because this adapter was made to fit both the Standard and Max versions of the AiraCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not affect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design with this flexibility to overcome the challenges of this airgun’s shroud design so that moderators could be used.

Key Features:
- Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants.
- Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel.
This part is designed and manufactured by DonnyFL
Select options
Sold out!
$60.00
DISCONTINUED
HP Strip Stak Pak for Evanix Air Speed
$60.00

Evanix Air Speed Air Stripper and Baffle Stack _
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. Air stripper come with o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$60.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter
Rated 5.00 out of 5
$60.00

Part fits Umarex Gauntlet 177, .22 or .25. Not compatible with the Gauntlet .30 Caliber.

This part is designed and manufactured by DonnyFL

Select options
$60.00
V3 6.26 inch Extension
Emperor/Ronin Extender
$60.00

THIS IS AN AIRGUN ONLY PART

Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it’s the latest model.

Select options
$99.00
Tanto 1.22 x 5 inches
Tanto 1.22 x 5 inches
$99.00

THIS IS AN AIRGUN ONLY PART

This part is designed and manufactured by DonnyFL

Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

Select options
$120.00
DonnyFL FX Suppressor
FX/DonnyFL 1.36 x 5 inches
$120.00

THIS IS AN AIRGUN ONLY PART

This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.

Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

Select options
Sale!
$125.00 – $130.00
Chronograph by Nate
NateChrony V2
$125.00 – $130.00

The NateChrony is a barrel mounted ballistic chronograph for all Air Rifles. It is accurate, affordable, super easy to use, and best of all – no more missed readings! The NateChrony mounts onto your barrel with one of the adapters for perfect alignment every time.
Using your mobile phone as the screen and battery, means you get the best display on the market and never get surprised by a flat battery in your Chronograph.

The NateChrony is fully featured and will provide all the data even the most demanding tuner requires. It displays a current shot string, and has four additional save slots – all of which retain the data when power is lost. You can configure pellet weight, display hold time, and adjust the NateChrony readings to match another Chronograph.

Specifications

Accuracy: calibrated to be within 1fps of actual pellet speed at 1,000fps from a certified set of master chronographs
Resolution: <0.1fps shot to shot at 1,000fps
Air powered guns only
CO2 power can cause vapour, not recommended
Maximum caliber: ~45-50 cal (depending on power)
Maximum power: 150 fpe

Select options