Moderators/Suppressor/Adapters

Suppressors, Silencers, and Adapters.

$11.00 – $22.00
Nate Chrony Custom Adapters
Nate Chrony Custom Adapters
$11.00 – $22.00

Airgun Specific Custom Adapters

Select options
$12.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Aluminum Air Stripper
Rated 5.00 out of 5
$12.00

This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.

Part does not fit Gauntlet .30 caliber

This part is designed and manufactured by DonnyFL

Select options
$14.00 – $18.00
Adapter for NateChrony V2
NateChrony Variable Adapter
$14.00 – $18.00

A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.

Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.

The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.

Thumb screws are aluminum & supplied with either knurled or printed tabs.

Price is for 1 adapter, with 1 set of screws.

Select options
$20.00
HP Baffle Stack For Umarex Gauntlet
Rated 5.00 out of 5
$20.00

Part fits either the original Gauntlet or the Gauntlet 2

THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.

Select options
$27.00
5 Piece Stak Pak W/Spring
Barra 1100z Stak Pak W/Spring
$27.00

Only fits the 19.25″ barrel length version. Middle to late 2023 produced 1100Z barrels were increased in length to 22.25″ eliminating the free space that used to allow a spring and baffles to fit.

Help quiet down your Barra 1100z with our custom-fit HP 5-piece Baffle Stak and tension spring. There are two different-sized baffles to help eliminate patterned harmonics in the air stream.

Select options
$28.00
HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
Rated 5.00 out of 5
$28.00

Part fits either the original Gauntlet or the Gauntlet 2

You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.

Air Stripper comes with o-ring and silicone grease for installation.

Select options
Sold out!
$35.00
Evanix Rainstorm II Baffle Stack
$35.00

Evanix Rainstorm II Baffle Stack

Here is an 8 piece multi-sized baffle stack for the Evanix Rainstorm/Rainstorm II. The HP Baffle Stack strips away turbulent air and sound from the shot signature of the Umarex Gauntlet. The baffles trap sound and air in each cavity and force it to stay in the moderator chamber away from the pellet path.
The Rainstorm HP Baffle Stack requires the non cone STAND OFF to be sized by the user. You will need to sand the STAND OFF down to the required height for your rifle.
The HP Baffle Stack should be installed as follows, from the front, further-est from the barrel, Short/Full/Full/Short/Short/Full/Full/Standoff at the muzzle.

Baffles should be pointing towards the breech

<= Towards the breech —— Towards the Muzzle of shroud =>

[░░] <░] <░░] <░░] <░] <░] <░░] <░░] CAP
SO SC NC NC SC SC NC NC

SO = STAND OFF
NC = NORMAL CONE
SC = SHORT CONE

Select options
Sold out!
$35.00
Artemis PP750 1/2 x 20 #A68
$35.00

Fits the Artemis PP750 PCP

This part is designed and manufactured by DonnyFL

Read more
Sale!
Original price was: $39.99.Current price is: $35.00.
HP Stak Pak for Hatsan QE
Rated 5.00 out of 5
Original price was: $39.99.Current price is: $35.00.

Stak Pak for Hatsan QE shrouds (.357, .457, or QE screwed in place open sights Not Included)

Unscrew your shroud end cap, remove the two felt-covered stock baffle assemblies, remove the two aluminum stand-off chambers, and install the Hajimoto Stak Pak. No tools, no modifications, just a simple one-for-one swap! Some model Hatsans will use all the baffles others will need one less full-sized baffle, be sure to use both shorter baffles and leave out the full-sized one. If you need to leave one out, leave out the first full-sized baffle and then arrange the stack as shown in the packaging.

A ten-piece kit that directly replaces the two hair curler style baffles inside any Hatsan with a QE shroud system, excluding .357 & .457 models. The bundle has nine baffle chambers to help remove noise and turbulence in the air stream. The baffle stack rides on a high-tension compression spring allowing for a perfect fit for any Hatsan QE PCP, excluding .357, .457, and models with the fixed sight on the QE swell that are screwed into an internal ring.

The result is a more laminar air stream which reduces projectile instability and substantially changes the sound of the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A24 adapter.

If your QE shroud has a fixed sight that is screwed to a ring that is inside the QE swell section of the shroud, you cannot use the HP STAK PAK.

Installation video is listed in the DESCRIPTION section below

Select options
$35.00
RTI Priest 2 Shroud Extender #A66
RTI Priest 2 Shroud Extender #A66
$35.00
If your Priest shroud sits behind the air bottle and you would like to use a larger suppressor, this extender will allow you to do so.

Features:
- 6061 T6 aluminum
- Knurled cap
- Matte black anodize
Select options
Sold out!
$35.00
DonnyFL KOI/Tanto Endcaps
$35.00

KOI and Tanto End caps in 1/2 x 20 threads

Select options
$35.00
Replacement end caps
Emperor/Ronin End Caps
$35.00

THIS IS AN AIRGUN ONLY PART

Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.

Select options