Air Rifle Mods/Parts

$45.00
Beeman Underlever 1357 | 1358 Adapter #A86
$45.00

Specifically for the Beeman 1357 / 1358

This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o’ring and put it on the new adapter.

This part is designed and manufactured by DonnyFL

Select options
$47.00
Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00

UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Avenger

A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$47.00
Origin .22/.25
HP Strip Stak Pak for Origin
Rated 4.33 out of 5
$47.00

NEW ENHANCED DESIGN

UPDATE: The newer Origins have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

Strip Stak Pak for the Umarex Origin
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. I strongly recommend that you watch my installation video below.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$50.00
DonnyFL A115 JTS Adapter
JTS Airacuda Adapter #A115
$50.00
Specifically for the Airacuda Standard or the Max in any Caliber (.22, .25, or .30)

Because this adapter was made to fit both the Standard and Max versions of the AiraCuda, and because of the variations between individual rifles, you may find that one or two threads remain exposed when you snug the adapter in place. This is normal, and will not affect the performance of the rifle. In fact, our testing has revealed that a longer or heavier moderator can be used with less risk of clipping as compared to the endcap-only style adapter. It was necessary to design with this flexibility to overcome the challenges of this airgun’s shroud design so that moderators could be used.

Key Features:
- Compatibility: Perfect fit for JTS Aircuda and Aircuda MAX rifles. Suitable for .22, .25, .30 caliber variants.
- Premium Material: Made with high-grade 6061 aluminum, ensuring durability and a lightweight feel.
This part is designed and manufactured by DonnyFL
Select options
$55.00
11.4cc plenum expansion for Avenger
Doux – Avenger Power Plenum
$55.00
AVENGER/LEVIATHAN POWER PLENUM:
- SIZE: 11.4cc
- STACKABLE
- BLACK ANODIZED WITH MATT BLACK GUN COATING
- TYPICAL PERFORMANCE INCREASE IS AROUND 20FT/S WITH NO OTHER MODIFICATIONS.
THIS PLENUM IS NOT DESIGNED TO NOT FIT THE BULL PUP VERSION

INSTALLATION CAN BE MADE USING TYPICAL SNAP RING PLIERS

MADE IN SOUTH AFRICA

Installation video below
Select options
$59.99
Clamp with Pic rail
Saber Tactical 55mm Clamp
$59.99

If you’re uneasy about drilling into your factory gun stock, this 52mm bottle clamp will easily attach to your 52mm carbon fiber or aluminum bottles. It has rubber pads on the inside to prevent any marring to your bottle.

Fits perfectly for Umarex Gauntlets Stock tanks.

This clamp has picatinny rails at the bottom for you to connect your preferred picatinny accessories.

Select options
Sold out!
$60.00
DISCONTINUED
HP Strip Stak Pak for Evanix Air Speed
$60.00

Evanix Air Speed Air Stripper and Baffle Stack _
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. Air stripper come with o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$60.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter
Rated 5.00 out of 5
$60.00

Part fits Umarex Gauntlet 177, .22 or .25. Not compatible with the Gauntlet .30 Caliber.

This part is designed and manufactured by DonnyFL

Select options
$60.00
V3 6.26 inch Extension
Emperor/Ronin Extender
$60.00

THIS IS AN AIRGUN ONLY PART

Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it’s the latest model.

Select options
$65.00
Gauntlet Regulator Tester
$65.00

Assembled and tested by Hajimoto using quality US Parts! Don’t guess what the output of your Gauntlets regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.

Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like these shown

Select options
Sale!
$75.00 – $85.00
Gauntlet STK
Super Tune Kit (STK) for Gauntlet 1 and 2
Rated 5.00 out of 5
$75.00 – $85.00
THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)

For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

CONTENTS:
- Adjuster Plug Assembly.
- Smaller, Lighter Composite Poppet.
- Hajimoto Hammer Spring (Black Long)
- Lighter Trigger Spring (Bright Small).
- 5/64″ Allen Wrench For Adjusting Power.
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.

Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:

Written Detailed Tuning Instructions for the STK

More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there.
Select options
$79.00 – $99.00
FX No Limit Scope Rings 1″, 30mm and 34mm
$79.00 – $99.00

FX shows that they are able to innovate not just within airguns themselves, but in other areas of the shooting sports. The FX No Limit scope rings are perfect for long-range shooting as you can vertically adjust and angle your mounts so you can always find the sweet spot on your scope. These rings are also very useful if you need to have your scope higher off the receiver to allow for oversized magazines or scope camera setups.

You will want these rings if you are planning on using my Expanded Magazine.

Select options

BACK FROM RMAC

PLEASE BE PATIENT WITH US

AS WE GET CAUGHT UP