Description
Please be sure to measure your free area or clearance between the bottom of your scope to the top of the magazine well.
The HP Mini magazine height is 40.90MM (1.610″) compared to the much larger 50mm expanded mag
Avenger/Origin Mini Magazine
$33.00
Introducing the HP Mini Magazine.
The same reliable design as our expanded magazine but shorter to allow the mag to fit under your optic without the need to adjust or swap out your scope rings.
The HP Mini magazine is designed to fit the Avenger and Origin in .22 and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload.
The stands only 40.90mm (1.610″ a little less than 5/8″)
The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell, maybe
Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .22 = 13 shots
- .25 = 11 shots
- The magazine height is 40.90mm (1.610″ a little less than 5/8″)
- Mags also fit the Avenger Bullpup II
Please note that the actual finish may differ from that shown in the photos.
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
You must be logged in to post a review.
You may also like…
-
$79.00FX No Limit Scope Rings 1″, 30mm and 34mm – 30mm/Picatinny
$79.00Add to cartTube/Rail Option: 30mm/Picatinny
-
$79.00FX No Limit Scope Rings 1″, 30mm and 34mm – 30mm/Dovetail
$79.00Add to cartTube/Rail Option: 30mm/Dovetail
-
Sold out!
$99.00Eaglevision INS Mount
Infinity INS Elevation Adjustable Scope Mount 30mm Ring Picatinny
$99.00Read more
Eaglevision has designed and developed an amazing scope mount that allows the scope to move vertically along a guided path. The mount is lockable in different positions using two screws. This mount can be used as a low profile or be adjusted to the high profile too if your scope objective is too close to your rifle barrel or shroud. These mounts resolve a lot of problems for shooters who like to shoot long range and often run out of adjustment clicks on their turrets.
The mount can also come in handy if you have not been able to use your favorite scope due to lack of space between the rings or the odd position of your dovetail or Picatinny rail on your gun. We are very proud of this product as it became a “must-have” for people who love their bullpups.
The best application of this mount however is for people who want to reach out further than their ordinary mounts allow them to. By keeping the front mount at its lowest and elevating the rear mount to the highest point you can zero in your gun far beyond your normal mounts allows you to, without using the clicks on your turrets hence keeping the optical center of your scope intact (the ideal situation for long-range shooting).Another great feature is these mounts allow the scope to be lifted to allow for large or expanded magazines.
Item includes:
- 2 x infinity scope mount.
- 2 x allen key (different sizes).
- 4 x spears screws.
- 1 x large spear screw.
- Protection ring fabric.
- Waterproof case.
Related products
-
$28.00HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
$28.00Select options This product has multiple variants. The options may be chosen on the product pagePart fits either the original Gauntlet or the Gauntlet 2
You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.
Air Stripper comes with o-ring and silicone grease for installation.
-
$30.00Intended for higher power builds
High Travel Valve Stop For Umarex Gauntlet 1 or 2
$30.00Select options This product has multiple variants. The options may be chosen on the product pageThis part replaces part #19 and allows for greater valve dwell producing more power to be produced at higher regulator pressure settings.
The .22 caliber HTVS for the Generation 1 Gauntlet fits both the .177 and .22. Do not order Generation 1 HTVS for the Generation 2 Gauntlet, they are not the same
-
$18.50Umarex Gauntlet Regulator Shim Pak
$18.50Select optionsHajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
Reviews
There are no reviews yet.