Barrel Service Notos
$110.00
Notos Barrel Service
This is what we do to our Haji-Notos Custom Builds. but you can have the same service performed on your Notos barrel as well. The Transfer port work increases the port and polishes the opening to allow greater airflow to produce more power more efficiently.
You ship us your Notos Barrel and we execute the following:
- Remove the fixed molded plastic suppressor (the suppressor is destroyed in the process).
- Increase and polish the barrel transfer port.
- Two new barrel o-rings are provided.
- Clean up and polish the barrel crown.
- 1/2 x 20 UNF Threaded Adapter Included.
- Barrel Shroud End Cap and Barrel Guide Included.
- Thoroughly clean and silicone barrel bore.
Notos Barrel Removal
Your Barrel is very easily removed by removing the 2.5mm button head screw on top of the Picatinny rail near the magazine opening. Once the 2.5mm screw is removed, there is a 2mm set screw below it that holds the barrel into the receiver block. Loosen the 2mm screw four revolutions and slide out the barrel.
Shipping
When you place the order for the above-described service, we will send you an order processing notification with a copy of your invoice. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your barrel for modification.
Additional information
| Weight | 32 oz |
|---|---|
| Dimensions | 14 × 2 × 2 in |
You must be logged in to post a review.
Related products
-
$205.00Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
$205.00Select optionsIntroducing a Hajimoto Productions Exclusive offer!
22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSIFlex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSIIf you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE
Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
-
$20.00HP Baffle Stack For Umarex Gauntlet
$20.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.
-
$12.00for .177, .22 and .25 NOT .30
Umarex Gauntlet Aluminum Air Stripper
$12.00Select options
This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.
Part does not fit Gauntlet .30 caliber
This part is designed and manufactured by DonnyFL
Reviews
There are no reviews yet.