Adapter for NateChrony V2
Price range: $14.00 through $18.00
A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.
Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.
The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.
Thumb screws are aluminum & supplied with either knurled or printed tabs.
Price is for 1 adapter, with 1 set of screws.
Additional information
| Weight | 6 oz |
|---|---|
| Dimensions | 6.25 × 3.25 × 2 in |
| Size | 35mm-15mm (S), 45mm-15mm (L) |
You must be logged in to post a review.
Related products
-
$50.00Reg Pressure Tester
HubenPower Regulator Tester
$50.00Select options
High quality HubenPower reg tester.
Features
- Micro threaded activation knob.
- Built in quick action pressure relief knob.
- High pressure gauge to 6000 psi.
Don’t guess what the output of your regulator is, KNOW what it is especially if you are adding shims and need to hit a specific PSI output.
Designed to be used with any Paintball style Regulator that uses the industry-standard G1/2-14 Threads like those shown below.
-
$130.00Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
$130.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
$47.00Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00Select optionsUPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.Replacement Air Stripper 0-ring is 14mm x 1.5mm
Reviews
There are no reviews yet.