$60.00
Evanix Air Speed Air Stripper and Baffle Stack _
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. Air stripper come with o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
You must be logged in to post a review.
Related products
-
for .177, .22 and .25 NOT .30
Umarex Gauntlet Strip Stak Pak (Bundle)
$45.00Select optionsHajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.
Air Stripper comes with o-ring and silicone grease for installation.
-
Sale!
Gauntlet STK
Super Tune Kit (STK) for Gauntlet 1 and 2
Rated 5.00 out of 5$75.00 – $93.00Select optionsTHIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCKThe single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!
Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)
For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLETCONTENTS:
- Adjuster Plug Assembly.
- Smaller, Lighter Composite Poppet.
- Hajimoto Hammer Spring (Black Long)
- Lighter Trigger Spring (Bright Small).
- 5/64″ Allen Wrench For Adjusting Power.
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:Written Detailed Tuning Instructions for the STK
More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there. -
Intended for higher power builds
High Travel Valve Stop For Umarex Gauntlet 1 or 2
$30.00Select optionsThis part replaces part #19 and allows for greater valve dwell producing more power to be produced at higher regulator pressure settings.
The .22 caliber HTVS for the Generation 1 Gauntlet fits both the .177 and .22. Do not order Generation 1 HTVS for the Generation 2 Gauntlet, they are not the same
Reviews
There are no reviews yet.