$40.00
Please note that when you add a suppressor to this gun, it does not properly index the magazine. If you plan to single load and use a suppressor that’ll be fine. I would also recommend using a suppressor one caliber size up to reduce the chance of pellet clipping.
5 in stock
1/2 x 20 UNF adapter for those rapid firing Bullmaster. New and improve design to allow more air flow.
Features:
| Weight | 4 oz |
|---|---|
| Dimensions | 1 × 1 × 1.5 in |
You must be logged in to post a review.
THIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
THIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Tatsu 1.6 x 4.25 inches
THIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Stak Pak for Hatsan QE shrouds (.357, .457, or QE screwed in place open sights Not Included)
Unscrew your shroud end cap, remove the two felt-covered stock baffle assemblies, remove the two aluminum stand-off chambers, and install the Hajimoto Stak Pak. No tools, no modifications, just a simple one-for-one swap! Some model Hatsans will use all the baffles others will need one less full-sized baffle, be sure to use both shorter baffles and leave out the full-sized one. If you need to leave one out, leave out the first full-sized baffle and then arrange the stack as shown in the packaging.
A ten-piece kit that directly replaces the two hair curler style baffles inside any Hatsan with a QE shroud system, excluding .357 & .457 models. The bundle has nine baffle chambers to help remove noise and turbulence in the air stream. The baffle stack rides on a high-tension compression spring allowing for a perfect fit for any Hatsan QE PCP, excluding .357, .457, and models with the fixed sight on the QE swell that are screwed into an internal ring.
The result is a more laminar air stream which reduces projectile instability and substantially changes the sound of the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A24 adapter.
If your QE shroud has a fixed sight that is screwed to a ring that is inside the QE swell section of the shroud, you cannot use the HP STAK PAK.
for .177, .22 and .25 NOT .30
This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.
Part does not fit Gauntlet .30 caliber
This part is designed and manufactured by DonnyFL
Fits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s
This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.
If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.
This part is designed and manufactured by DonnyFL
Reviews
There are no reviews yet.