FX No Limit Scope Rings 1″, 30mm and 34mm

FX No Limit Scope Rings 1", 30mm and 34mm
FX No Limit Scope Rings 1", 30mm and 34mm - Image 2
FX No Limit Scope Rings 1", 30mm and 34mm - Image 3
FX No Limit Scope Rings 1", 30mm and 34mm - Image 4
FX No Limit Scope Rings 1", 30mm and 34mm - Image 5
FX No Limit Scope Rings 1", 30mm and 34mm - Image 6
FX No Limit Scope Rings 1", 30mm and 34mm - Image 7
FX No Limit Scope Rings 1", 30mm and 34mm - Image 8
FX No Limit Scope Rings 1", 30mm and 34mm - Image 9

$79.00 – $99.00

FX shows that they are able to innovate not just within airguns themselves, but in other areas of the shooting sports. The FX No Limit scope rings are perfect for long-range shooting as you can vertically adjust and angle your mounts so you can always find the sweet spot on your scope. These rings are also very useful if you need to have your scope higher off the receiver to allow for oversized magazines or scope camera setups.

You will want these rings if you are planning on using my Expanded Magazine.

Clear
SKU: HPAFXNL30 Categories: , , , ,

Description

The FX No Limit scope mount has so many more benefits than the average user can appreciate. They are available in Dovetail which is a perfect match for the Gauntlet.

Some of the major benefits are:
* They allow you to optically center your scope and only use the turrets to fine adjust to the POI.
* They allow you to mount any sized objective lens you want.
* They give you the ability to eliminate any barrel droop scenarios that you may have on an airgun as you are able to independently raise or lower either mount.
* Last and not least, these mounts allow to gain substantial minutes of angle for long-range shooting without exposing your scopes elevation turret adjustment to its maximum.

Additional information

Weight 7 oz
Dimensions 8 × 4 × 1 in
Tube/Rail Option

34mm/Dovetail, 34mm/Picatinny, 30mm/Dovetail, 30mm/Picatinny, 1"/Dovetail, 1"/Picatinny

Reviews

There are no reviews yet.

Be the first to review “FX No Limit Scope Rings 1″, 30mm and 34mm”

Related products

  • Gauntlet Flex Reg with 22ci Tank - Hajimoto ConfigurationsGauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
    $205.00

    Hajimoto Flex Reg on 22ci Aluminum 3K for the G1

    Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations
    $205.00

    Introducing a Hajimoto Productions Exclusive offer!

    22ci/360cc/.36L Aluminum Tank 3000PSI
    Newly redesigned unit
    Now has a high pressure and low pressure burst discs!

    Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
    Stock .177/.22 | 3000/1100PSI Regulator
    Flex 22 .177/.22 |3000/700 to 1500PSI

    Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
    Stock .25 | 3000/1900PSI Regulator
    Flex 22 .25 | 3000/1500 to 2300PSI

    If you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE

    Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.

    A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!

    The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

    The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.

    Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

    The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!

    When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.

    Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

    Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.

    Select options
  • Regulator Service or Pressure Change
    $45.00

    Regulator Service or Pressure Change

    Regulator Service or Pressure Change
    $45.00

    This is a service to repair, test, leak test, adjust or increase the output pressure of a Umarex Gauntlet 1 or 2, regulator to a customer’s requested output. The regulator will be tested and calibrated to within +/- 75 PSI. Parts such as Gauges, Burst discs, Bonnets, Pistons, Caps, or Regulator bodies are not included. If parts are determined to be required to repair the regulator, pricing will be determined, quoted, and will need to be paid prior to the return of the regulator.

    Please note that if you have a Taiwan-produced regulator, which is the regulator that is located at the top of the photo, there are very limited corrections that can be made to these units and you may end up needing a new regulator. Please use the notes area to provide the Generation and caliber of the rifle. Also, give as much detail as possible of the issue or the requested pressure output and so forth.

    Once the order is physically reviewed, you will receive a second notification with details associated with packaging and shipping the items in for service.

    When you place the order for the above-described service, you will receive an order processing notification. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your regulator or regulator and tank assembly.

    This service is not a hydro test of the tank/bottle and is focused only on the regulator’s functionality and visual inspection assemblies.

    Please note that this service is not associated with any manufacturer’s warranty, so please be sure to exhaust all warranty options prior to sending us your regulator for service as our working on the part voids any manufacturer-provided warranties.

     

    Select options
  • HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
    $28.00
    HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
    $28.00

    Part fits either the original Gauntlet or the Gauntlet 2

    You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.

    Air Stripper comes with o-ring and silicone grease for installation.

    Select options

Copyright All rights reserved Hajimoto Productions LLC 2025

Proudly powered by WordPress . Theme: multipurpose shop by eDataStyle.