FX No Limit Scope Rings 1″, 30mm and 34mm

Related products

• 

  $11.00 – $20.00Price range: $11.00 through $20.00

  For G1 G2 & G30 Variants

  Umarex Gauntlet Tune O-ring Kit

  $11.00 – $20.00Price range: $11.00 through $20.00

  Hajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2

  Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.

  

  I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.

  Some of the NO-Ring seals have the leading edge precision ground.
  

  These tapered / precision ground types need to be installed as shown below

  

  (Images are of the .30 caliber NO RING)

  You get:

  • 2  of pellet probe NO-ring seals.
  • 2 sets of barrel o-rings.
  • 2 sets of tank block o-rings.
  • 2  of valve body o-rings.

  

  

   

  Select options

• 

  $45.00

  for .177, .22 and .25 NOT .30

  Umarex Gauntlet Strip Stak Pak (Bundle)

  $45.00

  Hajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
  An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

  BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
  Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.
  

  Air Stripper comes with o-ring and silicone grease for installation.
  

   

   

  Select options

• 

  $150.00

  Sumo 1.6 x 6.25 inches

  $150.00

  THIS IS AN AIRGUN ONLY PART

  

  This part is designed and manufactured by DonnyFL

  Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
  If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
  The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
  The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
  The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.

  The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.

  Select options