$60.00
THIS IS AN AIRGUN ONLY PART
Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it’s the latest model.
https://youtu.be/Oyo7uq2vHr0
*DISCLAIMER: These DonnyFL products are INTENDED for the use on airguns only. It is a violation of Federal law to use this product in a manner inconsistent for which it was intended for. It is your Responsibility to know the laws in your state, county and city and to fully comply with them.
| Weight | 6 oz |
|---|---|
| Dimensions | 6.5 × 2.5 × 2.5 in |
| Thread Size | 1/2X20 S5D, M18x1 S5C, M20x1 S5E, M14x1.25 S5F |
You must be logged in to post a review.
Gauntlet STK
THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK
The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!
Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile and there is no better chronograph than the FX Pocket Radar V2. (Power examples given are the .22 caliber version Gauntlet 1)
For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET
CONTENTS:
The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.
Be sure to follow my written instructions in the document below.
Use the video to install but follow these written instructions to adjust and tune the STK:
Written Detailed Tuning Instructions for the STK
More details below.
Always read the content below because any revised instructions, video, photos, or other links will be there.
Installation Video for 1.5″ Picatinny rail on the Umarex Gauntlet forearm.
THIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.
The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Reviews
There are no reviews yet.