Umarex Parts/Mods

50 to 250
For either G30 or G30SL
G30 Barrel Service Lab
50 to 250
Select options
$7.00
Gauntlet Barrel Baffle Spring
Umarex Gauntlet Baffle Spring
$7.00

Umarex Gauntlet .177, .22, or .25 Baffle Spring.

Part is not compatible with Gauntlet .30 Caliber

This is the spring that lives in your Gauntlets Shroud. It is required to keep the air stripper on the end of the barrel and allows the baffle or baffle stack to live under tension.

Select options
$9.95
Burst Disk Two Pack
Regulator Burst Disks 1.8k, 3k, 5k & 7.5k
$9.95
- 1.8k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 3k burst disk is used as the low-pressure burst disk on 3k and 4,5k tanks
- 5k burst disk is used as the high-pressure burst disk on 3k tanks
- 7.5k burst disk is used as the high-pressure burst disk on 4.5k tanks
Actual burst disk finish may be Black, or Bright depending on availability.
Select options
Sale!
Original price was: $14.99.Current price is: $9.99.
QD PORT SLING SWIVEL AND BASE
Original price was: $14.99.Current price is: $9.99.

QD Sling Mount Sling Swivel Quick Detach Release Push Button QD Sling Swivels for MLOK SLOTS.

Quick Disconnect

Select options
$12.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Aluminum Air Stripper
Rated 5.00 out of 5
$12.00

This part is for the Umarex Gauntlet 1 or 2 in .177, .22, or .25 Calibers.

Part does not fit Gauntlet .30 caliber

This part is designed and manufactured by DonnyFL

Select options
Sale!
Original price was: $17.95.Current price is: $14.00.
Stock Umarex Magazine
Umarex Gauntlet Rotary Magazine
Original price was: $17.95.Current price is: $14.00.
The Gauntlet Rotary Magazine advances each pellet with the operation of the bolt on the Umarex Gauntlet PCP air rifle.

Features
- .177 = 12 shots
- .22 = 10 shots
- .25 = 8 shots
- .30 = 7 shots
Select options
$15.00 – $70.00
Bipod and Picatinny Rail
$15.00 – $70.00

Installation Video for 1.5″ Picatinny rail on the Umarex Gauntlet forearm.

Select options
$17.00
Gauntlet 1 and Gauntlet 2
Umarex Gauntlet Tune O-ring Kit
$17.00
Hajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2

Now includes my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.

I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.

Some of the NO-Ring seals have the leading edge precision ground.

These tapered / precision ground types need to be installed as shown below

(Images are of the .30 caliber NO RING)

You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
Select options
$18.50
Umarex Gauntlet Regulator Shim Pak
$18.50
Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet

I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.

The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
  (Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.

DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.

Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.

You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.

If you rapid fill, there is a good chance you will pop your burst disc.
Select options
$20.00
HP Baffle Stack For Umarex Gauntlet
Rated 5.00 out of 5
$20.00

Part fits either the original Gauntlet or the Gauntlet 2

THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.

Select options
$28.00
HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
Rated 5.00 out of 5
$28.00

Part fits either the original Gauntlet or the Gauntlet 2

You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.

Air Stripper comes with o-ring and silicone grease for installation.

Select options
$30.00 – $35.00
Fits Gauntlet 1, 2 even the .30 Cal
HP Barrel Band For Umarex Gauntlet
Rated 5.00 out of 5
$30.00 – $35.00

Available in the classic Picatinny rail version or the 15mm thick rail less version.

Fits both the original Gauntlet as well as the Gauntlet 2 including the G30 or G30SL!

Select options
$30.00
Intended for higher power builds
High Travel Valve Stop For Umarex Gauntlet 1 or 2
$30.00

This part replaces part #19 and allows for greater valve dwell producing more power to be produced at higher regulator pressure settings.

The .22 caliber HTVS for the Generation 1 Gauntlet fits both the .177 and .22. Do not order Generation 1 HTVS for the Generation 2 Gauntlet, they are not the same

Select options
$30.00
Haji-Notos Mag 11 rounds
Notos Expanded Magazine
$30.00

Introducing the Haji-Notos 11 Shot Expanded Magazine!

This is a brand-new design that loads from the right and employs a removable magnetic lid for easy loading. Allow for a smooth and consistent chambering of rounds without issue.

Select options
$33.00
Gauntlet 1 or Gauntlet 2 Mini Magazine
HP Gauntlet, Mini Mag
$33.00
Introducing the HP Mini Magazine.

The same reliable design as our expanded magazine but shorter to allow the mag to fit under your optic without the need to adjust or swap out your scope rings.

The HP Mini magazine is designed to fit the Umarex Gauntlet 1 or 2 in .22 and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload.

The stands only 40.90mm (1.610″)

The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell, maybe

Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .22 = 13 shots
- .25 = 11 shots
- The magazine height is 40.90mm (1.610″ )
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
Select options
$35.00 – $40.00
For Gauntlet .177, .22, .25 and .30 Calibers
Hajimoto’s Gauntlet Expanded Magazine
Rated 4.00 out of 5
$35.00 – $40.00
Here is a high-quality, high-capacity magazine designed to fit the Umarex Gauntlet 1 or 2 in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjust rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.

The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell

Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .177 – 21 shots which is an increase of 110% more shots over the stock magazine!
- .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
- .25 = 15 shots which is an increase of 37.5% more shots over the stock magazine!
- .30 = 11 shots which is an increase of 57.5% more shots over the stock magazine!
- The magazine height for the .177, .22 and .25 is 50.25MM (1.978″)
- The magazine height for the .30 is 46.20MM (1.820″) Max Slug/Pellet length supported 11.20mm (0.441″)
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
Select options
$35.00 – $40.00
Fits both Avenger and Origin
HP Avenger Exp Mag
$35.00 – $40.00
Here is a high-quality, expanded capacity magazine designed to fit the Umarex Origin in .22 & .25 calibers as well as a version for Air Venturi Avenger in .177, .22 and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjust rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.

The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell

Features
- An easy to load NO LID design.
- No pre-winding is necessary.
- Easy partial fill design.
- .177 (Avenger only) – 21 shots which is an increase of 110% more shots over the stock magazine!
- .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
- .25 = 15 shots which is an increase of 87.5% more shots over the stock magazine!
- The magazine height of all calibers is 50.25MM (1.978″)
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
Select options
$35.00
Replacement end caps
Emperor/Ronin End Caps
$35.00

THIS IS AN AIRGUN ONLY PART

Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.

Select options
$40.00
For the Gauntlet 1 or 2
Umarex Gauntlet 1/2 x 20 adapter #A23
$40.00

This part is designed and manufactured by DonnyFL

Select options
$40.00
Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
$40.00

Fits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s

This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.

If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.

This part is designed and manufactured by DonnyFL

Select options
$40.00
Akela/Kratos Strip Stak Pak
HP Strip Stak Pak for Akela/Kratos
$40.00

INCLUDES NEW ENHANCED AIR STRIPPER DESIGN

Strip Stak Pak for the Benjamin Akela and Kratos PCP’s
A nine-piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides variable-sized baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A8 adapter.
The Air Stripper is threaded and comes with an o-ring and silicone grease for installation. The stock barrel shroud spring must be reused.

Replacement Air Stripper 0-ring is 14mm x 1.5mm

Select options
$45.00
for .177, .22 and .25 NOT .30
Umarex Gauntlet Strip Stak Pak (Bundle)
$45.00

Hajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.

BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.

Air Stripper comes with o-ring and silicone grease for installation.

Select options
$45.00
Regulator Service or Pressure Change
Regulator Service or Pressure Change
$45.00

This is a service to repair, test, leak test, adjust or increase the output pressure of a Umarex Gauntlet 1 or 2, regulator to a customer’s requested output. The regulator will be tested and calibrated to within +/- 75 PSI. Parts such as Gauges, Burst discs, Bonnets, Pistons, Caps, or Regulator bodies are not included. If parts are determined to be required to repair the regulator, pricing will be determined, quoted, and will need to be paid prior to the return of the regulator.

Please note that if you have a Taiwan-produced regulator, which is the regulator that is located at the top of the photo, there are very limited corrections that can be made to these units and you may end up needing a new regulator. Please use the notes area to provide the Generation and caliber of the rifle. Also, give as much detail as possible of the issue or the requested pressure output and so forth.

Once the order is physically reviewed, you will receive a second notification with details associated with packaging and shipping the items in for service.

When you place the order for the above-described service, you will receive an order processing notification. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your regulator or regulator and tank assembly.

This service is not a hydro test of the tank/bottle and is focused only on the regulator’s functionality and visual inspection assemblies.

Please note that this service is not associated with any manufacturer’s warranty, so please be sure to exhaust all warranty options prior to sending us your regulator for service as our working on the part voids any manufacturer-provided warranties.

Select options
$45.00
Umarex Origin 1/2 x 20 Adapter #A70
$45.00

Specifically for the Umarex Origin

Not to be used with the Hajimoto Productions Strip Stak Pak (SSP) which is an Air stipper. Spring and Baffle Stack.

This version allows you to use a larger suppressor than the Tanto or KOI. Designed to slide over the barrel to keep the barrel centered with the adapter. This reduces the chance of pellet clipping and improves accuracy.

This part is designed and manufactured by DonnyFL

Select options

Introducing the Haji-Notos 11 Shot Expanded Magazine!

Introducing the HP Mini Magazine.