-
Sold out!
Allows for a dual Reg Setup
AE Swede Avenger Bottle Adapter
$88.00 – $325.00Select optionsThis is AE Swede’s bottle adapter and plug that allows the user to run dual regulators.
Here is where you will find the reg you need. Just select 3000PSI output. -
Tanto 1.22 x 5 inches
Tanto 1.22 x 5 inches
$99.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Fits the G1, G2 or G30
Real 2 Stage Trigger for the Gauntlet
Rated 5.00 out of 5$110.00Select optionsFull-fledged 2-stage trigger for the Umarex Gauntlet 1, 2 or G30. This trigger is a direct replacement for the single-stage trigger that ships with the Umarex Gauntlet. This trigger is a straightforward install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
- The Trigger Is Stainless Steel 17-4 Through Hardened
- The Trigger Shoe Is Aluminum 6061-T6
Please see the installation video below for more details.
Super Tune Kit Users
You must use the stock trigger return spring with the two-stage trigger as the trigger spring that comes with the Super Tune Kit is too light to be effective with the two-stage trigger. -
DonnyFL FX Suppressor
FX/DonnyFL 1.36 x 5 inches
$120.00Select optionsTHIS IS AN AIRGUN ONLY PART
This is a custom size that comes with FX airguns if you decide to upgrade the suppressor or if you are looking to add a suppressor that is right in between the Tanto and Tatsu. The FX/DonnyFL is the same length as the Tanto but slightly larger in diameter, comparable to the FX factory suppressor. This weighs around 4.7 ounces. Comes with a protective red tube for easy transport and storage.
Remember it is recommended that you order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
Rated 5.00 out of 5$130.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
for .177, .22 and .25 NOT .30
Gauntlet Short Shroud Combo
$130.00 – $215.00Select optionsThis part is designed and manufactured by DonnyFL for airgun use only
Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber
Stock baffle spring must be used!
Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.If Your Gauntlet is:
- .177 Get a .177/.22 Supressor
- .22 Get a .22/.25 Supressor
- .25 Get a .25/.30 Supressor
Get it?
-
Ninja X Reg Custom Output Regulator up to 3100psi
Ninja High Pressure 5/8″-18UNF Custom Output Regulator
$144.95Select options5/8″-18UNF thread can be used on 3000PSI bottle as well. This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.
We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.
You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.
This is a direct replacement for the regulator found on the Gauntlets G1, G2 and G30 Caliber
Take advantage of a quality regulator for your high pressure application. MADE IN THE USA! Ninja HP regulator output pressures in increments of 100PSI. Simply select your desired output pressure from 1100PSI TO 3100PSI All custom built pressure units will have a +/- 50 psi tolerance.
-
NEW MODEL
Pro V3 for 3K and 4.5K Cylinders
Ninja Pro V3 Regulator 5/8″ Thread
$148.00Select optionsThe All New Hajimoto Pro V3 in 5/8”-18UNF Thread with Stainless Steel Cap Threads
Ninja's Pro V3 with rotional bonnet. A perfect replacement for the regulator found on the on the Gauntlet 2. A complete regulator rebuild kit is included! MADE IN THE USA! Ninja regulator output pressures in increments of 100PSI. Simply select your desired output pressure. Output ranges from 1100PSI to 2400PSI. All custom built pressure units will have a +/- 50 psi tolerance.
-
5/8″-18UNF Threaded Unit
Flex Reg Hajimoto Configurations
$149.00 – $159.00Select optionsNewly redesigned unit
Now has a high pressure and low pressure burst discs!
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800PSI adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF
The Ninja Flex regulator is available in any 900PSI spread to a maximum of 3100PSI output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex RegFlex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/700 to 1500PSIFlex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1600 to 2400PSIFlex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1600 to 2400PSIFlex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSIComes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
-
Sumo 1.6 x 6.25 inches
$150.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 which is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
-
Ninja High Pressure Metric M18 Custom Output
$154.95 – $155.00Select optionsThe Hajimoto M18*1.5 Thread can be used on 3000PSI bottles as well.
The Bonnet is Steel not aluminum for maximum strength and low wear.
This regulator is built with the ball/pin and spring removed so hot swapping will not be able to happen.
We do include the ball/pin and spring should you happen to have a thin pin depression system capable of actually opening the valve.
You should never try and unscrew a high-pressure output paintball-style regulator (anything over 1000psi output) while it is under pressure. You will destroy the threads as they are not designed to be threaded on and off under load. Degas and then remove the regulator and bottle.
Take advantage of a quality regulator for your high pressure application. MADE IN THE USA! Ninja HP Metric regulator output pressures in increments of 100PSI. This is a M18 threaded regulator made for M18 threaded bottles. This will not fit Umarex Gauntlet Bottles which are 5/8"-18 Threaded. Simply select your desired output pressure from 1100PSI TO 3100PSI All custom built pressure units will have a +/- 75 psi tolerance. If you need a low output build with a fixed out of of something between 300 psi and 1100 psi, the CUSTOM pessure option and provide the output desired in the notes. If you are looking for a direct replacement for you Gauntlet2 .22, .25 & .30 You will want the 5/8"-18 Version that is found HERE