-
Umarex Gauntlet Regulator Shim Pak
$18.50Select optionsHajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
-
Swagalicous Hajimoto Productions Flat Bill Cap
Hajimoto Productions Flat Brim Cap
$19.00Select options -
HP Baffle Stack For Umarex Gauntlet
Rated 5.00 out of 5$20.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
THESE BAFFLES CANNOT BE USED INSIDE THE DONNYFL SHORT SHROUD.
-
Eaglevision
Eaglevision Tube Adapter Rings
$20.00 – $27.00Select optionsThis is high quality 30mm to 1″ or 34mm to 30mm scope tube adaptors, made of aluminium.
Designed To Works With All Eaglevision Scope Mounts.
-
Ninja X Reg Rebuild Kit
Ninja Paintball X Reg Rebuild Kit
$20.00 – $22.00Select optionsThis Kit Contains All Of The Most Consumable Parts in a NINJA X Reg
This Kit is for the Large X-Reg Piston Variant that measures 13.90mm in diameter at the flange of the large piston.
The Small section of the piston is 7.90mm in diameter.-
- 1 – User-selectable Burst Disk (1.8k, 3k, 5k, 7.5k
- 1 – Large Upper Large Piston O-Ring
- 1 – Small Lower Large Piston O-Ring
- 2 – Regulator Bonnet O-Rings
- 1 – Fill port o-ring
-
-
Ninja Regulator Rebuild Kit Part #NINJARBK
$21.95Select optionsNinja Paintball Tank Regulator Replacement Part #NINJARBK – Rebuild Kit for Ninja NON Pro Regulators.
User selectable included burst disc rating (1.8K, 3K, 5K or 7.5K)
-
Sale!
Inline high pressure filter
Mini Oil-Water Filter
$25.00Original price was: $25.00.$21.95Current price is: $21.95.Mini high pressure inline oil and water separator.
While it is not the largest and most effective oil-water separator, it offers some protection from moisture, oil, and dirt that would otherwise be pushed right into your PCP.
Due to the small capacity of the filter be sure to open the unit up, remove all the filters, and allow them to dry between uses else you run the risk of etching the cylinder or saturating the filters and forcing the trapped water, oil and debris into your PCP