Hatsan QE Big Bore .357/.457 M18x1 Adapter A54 #A54

Related products

• 

  $47.00

  Air Stripper, Tension Spring and Baffle Stack

  HP Strip Stak Pak for Avenger

  $47.00

  UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.

  Strip Stak Pak for the Avenger

  A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
  Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.

  Replacement Air Stripper 0-ring is 14mm x 1.5mm

  

  Select options This product has multiple variants. The options may be chosen on the product page

• 

  $35.00 – $40.00Price range: $35.00 through $40.00

  For Gauntlet .177, .22, .25 and .30 Calibers

  Hajimoto’s Gauntlet Expanded Magazine

  Rated 4.00 out of 5

  $35.00 – $40.00Price range: $35.00 through $40.00

  Now offering two designs. The original NO LOD and the new magnetic removable HP 2.0 design allows for much faster loading.

  Here is a high-quality, high-capacity magazine designed to fit the Umarex Gauntlet 1 or 2 in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload. Please remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjustable rings allow you to keep your scope optically center leaving all the turret adjustment-free to use when you need it.

  The NO LID design means you simply rotate the projectile carousel and drop in each round. There is no need to preload the spring, you are winding the spring during the loading process. This fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell

  Features

  • An easy to load NO LID design or the new magnetic lidded version.
  • No pre-winding is necessary.
  • Easy partial fill design.
  • .177 – 21 shots which is an increase of 110% more shots over the stock magazine!
  • .22 = 17 shots which is an increase of 70% more shots over the stock magazine!
  • .25 = 15 shots which is an increase of 37.5% more shots over the stock magazine!
  • .30 = 11 shots which is an increase of 57.5% more shots over the stock magazine!
  • The magazine height for the .177, .22 and .25 is 50.25MM (1.978″)
  • The magazine height for the .30 is 46.20MM (1.820″) Max Slug/Pellet length supported 11.20mm (0.441″)

  WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE

  Select options This product has multiple variants. The options may be chosen on the product page

• 

  $45.00

  Regulator Service or Pressure Change

  Regulator Service or Pressure Change

  $45.00

  This is a service to repair, test, leak test, adjust or increase the output pressure of a Umarex Gauntlet 1 or 2, regulator to a customer’s requested output. The regulator will be tested and calibrated to within +/- 75 PSI. Parts such as Gauges, Burst discs, Bonnets, Pistons, Caps, or Regulator bodies are not included. If parts are determined to be required to repair the regulator, pricing will be determined, quoted, and will need to be paid prior to the return of the regulator.

  Please note that if you have a Taiwan-produced regulator, which is the regulator that is located at the top of the photo, there are very limited corrections that can be made to these units, and you may end up needing a new regulator. Please use the notes area to provide the Generation and caliber of the rifle. Also, give as much detail as possible of the issue or the requested pressure output, and so forth.

  I wrote an article on the regulator change back in 2019, read all about HERE

  Once the order is physically reviewed, you will receive a second notification with details associated with packaging and shipping the items in for service.

  When you place the order for the above-described service, you will receive an order processing notification. Shortly after that, you will receive a detailed notification with the shipping information for you to ship us your regulator or regulator and tank assembly.

  This service is not a hydro test of the tank/bottle and is focused only on the regulator’s functionality and visual inspection assemblies.

  Please note that this service is not associated with any manufacturer’s warranty, so please be sure to exhaust all warranty options prior to sending us your regulator for service as our working on the part voids any manufacturer-provided warranties.

   

  Select options