$18.50
Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.
DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.
Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
2 in stock
You must be logged in to post a review.
Related products
-
Hajimoto Tune My Gauntlet G1 or G2
$625.00Select optionsWe completely tune your supplied Gauntlet 1 or 2 which includes everything listed in the section below.
The service includes a very detailed and time-consuming incoming inspection report that includes photos and other relevant information that detail the condition of the airgun and all of its pieces and parts. This report is provided to you and you must be reviewed and authorized in order for the work to continue.
Ordering procedures:
- Add all services and items to your cart.
- Be sure to use the notes section to communicate any known issues or special instructions.
- Check out.
Shortly after the order is received, you will receive an email notification containing shipping information that will include labeling and packaging requirements.
To better understand how the Gauntlet is transformed from a static you get what you get type of airgun, into an adjustable power and tunable PCP, take a look at this video that demonstrates how the power adjuster works if you should want to increase or decrease the power output for any given ammunition in order to get it to fly at the best rate of travel for that particular ammunition.
HOW TO ADJUST POWER WITH STKWe will build your order based on the information provided from the questionnaire as well as any specific requests, and before the airgun ships, any credits or additional charges will be settled.
-
Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50
$40.00Select optionsFits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s
This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.
If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.
This part is designed and manufactured by DonnyFL
-
Tatsu 1.6 x 4.25 inches
Tatsu 1.6 x 4.25 inches
Rated 5.00 out of 5$130.00Select optionsTHIS IS AN AIRGUN ONLY PART
This part is designed and manufactured by DonnyFL
Remember to always order your suppressor one size larger for shrouded barrel PCP’s.
If you have a .22 caliber shrouded barrel PCP, you’ll want to order a .25 caliber suppressor.
The .177/.22 is for shrouded barrel .177 or direct barrel threaded PCP’s in .22.
The .22/.25 is for shrouded barrel .22 or direct barrel threaded PCP’s in .25.
The .25/.30 is for shrouded barrel .25 or direct barrel threaded PCP’s in .30. The exception to this rule is the Gauntlet .30 is shrouded but because of the unique end cap, marries the barrel and shroud at the end.The Tanto, Tatsu, FX, or Sumo are not recommended for the Gauntlet .30 caliber because of the relatively small internal volume of these suppressors and the elevated operating pressures of the G30. We recommend the Ronin be used on all of our G30 Builds.
Reviews
There are no reviews yet.