Side Folding Stock Adapter #2

Related products

• Sale!

  

  $75.00 – $93.00Price range: $75.00 through $93.00

  Gauntlet STK

  Super Tune Kit (STK) for Gauntlet 1 and 2

  Rated 5.00 out of 5

  $75.00 – $93.00Price range: $75.00 through $93.00

  THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
  IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

  The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment, opening the possibility of higher or lower foot-pounds (FPE) for whatever the user desires. Do you need only 5FPE? No problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

  Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required to know the rate of travel of the projectile. (Power examples given are the .22 caliber version Gauntlet 1) 

  For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation, as there is a difference, and improperly selected kits are not returnable.
  BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

  CONTENTS:

  • Adjuster Plug Assembly.
  • Smaller, Lighter Composite Poppet.
  • Hajimoto Hammer Spring (Black Long)
  • Lighter Trigger Spring (Bright Small).
  • 5/64″ Allen Wrench For Adjusting Power.

  Be sure to follow my written instructions in the document below.
  Use the video to install but follow these written instructions to adjust and tune the STK:

  Written Detailed Tuning Instructions for the STK

  More details below.
  Always read the content below because any revised instructions, video, photos, or other links will be there.

  Select options
• Sold out!

  

  $40.00

  Liberty/Aspen/Avenger/Origin 1/2 x 20 #A50

  $40.00

  Fits the Nova Liberty, Aspen, AV Avenger, and Origin PCP’s

  This is a direct replacement end cap that when installed provides 1/2 x 20 UNF threads to allow the installation of your favorite moderator or suppressor. If you are looking for a better and stiffer barrel to barrel shroud connection that helps eliminate point-of-impact changes or projectile clipping issues, consider going with the A70 Adapter which essentially marries the barrel to the shroud.

  If you are a Hajimoto Productions Strip Stak Pak (SSP) user, then stick with the A50 because the A70 will not work with the SSP.

  

  This part is designed and manufactured by DonnyFL

  Read more
• Sold out!

  

  $18.50

  Umarex Gauntlet Regulator Shim Pak

  $18.50

  Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet

  I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.

  The shim kit contains:

  • 2 – #5 Shims.
  • 1 – #3 Shim.
  • 2 – #2 Shims.
    (Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)

  To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
  To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
  The included two #2 shims are for minor adjustments if you have a finicky regulator.

  DETAILED LESSON/EXAMPLE:
  Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.

  Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.

  You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.

  If you rapid fill, there is a good chance you will pop your burst disc.

  

   

  Read more