Regulator Burst Disks 1.8k, 3k, 5k & 7.5k

Related products

• 

  $130.00 – $215.00

  for .177, .22 and .25 NOT .30

  Gauntlet Short Shroud Combo

  $130.00 – $215.00

  

  This part is designed and manufactured by DonnyFL for airgun use only

  Part fits Gauntlet .177, 22 or the .25 caliber but does NOT fit the Gauntlet .30 caliber

   

  Stock baffle spring must be used!
  Remember to always order your suppressor one size larger for shrouded barrel PCP’s. DonnyFL Suppressors are sized so the first number is your PCP’s actual caliber and the second number is one size up. So if you owned a .22 caliber Gauntlet, the size you would select is .22/.25. If you had a .25 you would choose the .25/.30.

  If Your Gauntlet is:

  • .177 Get a .177/.22 Supressor
  • .22 Get a .22/.25 Supressor
  • .25 Get a .25/.30 Supressor

  Get it?

  Select options
  Quick view

• 

  $17.00

  Gauntlet 1 and Gauntlet 2

  Umarex Gauntlet Tune O-ring Kit

  $17.00

  Hajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2

  Now includes my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.

  

  I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.

  Some of the NO-Ring seals have the leading edge precision ground.
  

  These tapered / precision ground types need to be installed as shown below

  

  (Images are of the .30 caliber NO RING)

  You get:

  • 2  of pellet probe NO-ring seals.
  • 2 sets of barrel o-rings.
  • 2 sets of tank block o-rings.
  • 2  of valve body o-rings.

  

  

   

  Select options
  Quick view

• 

  $205.00

  Hajimoto Flex Reg on 22ci Aluminum 3K for the G1

  Gauntlet Flex Reg with 22ci Tank – Hajimoto Configurations

  $205.00

  Introducing a Hajimoto Productions Exclusive offer!

  

  22ci/360cc/.36L Aluminum Tank 3000PSI
  Newly redesigned unit
  Now has a high pressure and low pressure burst discs!
  
  

  Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
  Stock .177/.22 | 3000/1100PSI Regulator
  Flex 22 .177/.22 |3000/700 to 1500PSI

  Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
  Stock .25 | 3000/1900PSI Regulator
  Flex 22 .25 | 3000/1500 to 2300PSI

  If you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE

  Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
  
  

  A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!

  The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.

  The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.

  Consider picking up our extended foster fill adapter to make coupling and filling a breeze.

  The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!

  When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.

  Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

  Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.

  Select options
  Quick view