$146.00
The Hajimoto Ninja Paintball Pro V3 SHP in 5/8”-18UNF Thread with Stainless Steel Cap Threads
Ninja's Pro V3 SHP with rotional bonnet. A perfect replacement for the regulator found on the on the Gauntlet 2. A complete regulator rebuild kit is included! MADE IN THE USA! Ninja regulator output pressures in increments of 100PSI. Simply select your desired output pressure. Output ranges from 1100PSI to 2400PSI. All custom built pressure units will have a +/- 50 psi tolerance. Dont confuse the this regulator with the lower pressure SLP versions out there, there is a difference.
5/8''-18UNF Thread
Hajimotos Pro V3 with Stainless Steel 360 Cap.
The regulator body is made for both 3000PSI and 4500PSI
bottles with 5/8"-18UNF Threads.
Say goodbye to gauges and foster
nipples not lining up with the stock. (remember to degas before rotating)
American-made Ninja Regulator.
Custom output pressure for your
Umarex Gauntlet other custom build needs.
Output pressure is offered in 100 PSI increments from 1100 to 2400PSI.
| Weight | 8 oz |
|---|---|
| Dimensions | 5 × 2.5 × 2.5 in |
| Regulator Output | 1100 PSI, 1200 PSI, 1300 PSI, 1400 PSI, 1500 PSI, 1600 PSI, 1700 PSI, 1800 PSI, 1900 PSI, 2000 PSI, 2100 PSI, 2200 PSI, 2300 PSI, 2400 PSI |
| Tank Pressure | 3000 PSI, 4500 PSI |
You must be logged in to post a review.
Includes G1, G2, G30, G2SL, & G30SL variants
Available in the classic Picatinny rail version or the 15mm thick rail less version.
Versions for Gauntlet 1, Gauntlet 2, Gauntlet 30 as well as the SL Versions!
Air Stripper, Tension Spring and Baffle Stack
UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.
DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.
Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
Reviews
There are no reviews yet.