Description
Contains all the parts needed to rebuild the NINJA PRO V2 regulator
-
- 1 – User selectable Burst Disk
- 1 – Piston
- 3 – Blue Shims (0.10" EACH)
- 2 – Sets of 3 set screws
- 2 – White Seal Orings
$21.95
Ninja Paintball Tank Regulator Replacement Part #PRORBK – This Rebuild Kit for Ninja Pro V2 Regulators ONLY.
Like the one below:
This rebuild kit is not for the Umarex Gauntlet Stock Regulator.
User selectable included burst disc rating (1.8K, 3K, 5K or 7.5K)
Contains all the parts needed to rebuild the NINJA PRO V2 regulator
Weight | 2 oz |
---|---|
Dimensions | 1.5 × 2 × 1 in |
Burst Disc Rating | 1.8K, 3K, 5K, 7.5 |
You must be logged in to post a review.
for .177, .22 and .25 NOT .30
Hajimoto Productions Strip Stak Pak for the Gauntlet 1 or 2. Not compatible with the Gauntlet .30 Caliber.
An efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The HP Air stripper 2.0 comes with an o-ring. The kit also provides variable baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle.
BAFFLES CAN NOT BE USED WITH DONNYFL SHORT SHROUD
Because the Short Shroud is cut at a length that is a perfect fit for the air stripper and the spring. There is not any room for the baffles in the DonnyFL Short Shroud.
Air Stripper comes with o-ring and silicone grease for installation.
Hajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.
DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.
Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
5/8″-18UNF Threaded Unit
Were expect to have these back in stock by 11/20/2024
Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
Say goodbye to only one fixed output pressure!
The user has an 800PSI adjustment swing!
Requires minor forestock modification.
The regulator thread is 5/8-18UNF
The Ninja Flex regulator is available in any 900PSI spread to a maximum of 3100PSI output but for the Gauntlet select from the proper configuration.
If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.
How to read the below configurations
Example: Flex Reg .22 | 4500/1600 to 2400 psi
Flex Reg .22 = Regulator Type for .22 caliber
4500/ = The bottle’s maximum fill pressure
1600 to 2400 psi = The output range of the Flex Reg
Flex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex Reg .177/.22 |3000/700 to 1500PSI
Flex Reg Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex Reg .25 | 3000/1600 to 2400PSI
Flex Reg Configuration For Generation 2 Gauntlet .22 Cal
Stock .22 | 4500/1900PSI Regulator
Flex Reg .22 | 4500/1600 to 2400PSI
Flex Reg Configuration For Generation 2 Gauntlet .25 Cal
Stock .25 | 4500/2100PSI Regulator
Flex Reg .25 | 4500/1600 to 2400PSI
Flex Reg Configuration For G30 Cal
Stock .30 | 4500/2800PSI Regulator
Flex Reg .30 | 4500/2100 to 3100PSI
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Copyright All rights reserved Hajimoto Productions LLC 2024
Proudly powered by WordPress . Theme: multipurpose shop by eDataStyle.Please be sure to understand our return policies prior to making your purchases. All products offered on our website are intended for use on airguns only. It is a violation of Federal Law to use a product in a manner inconsistent with its intended labeling or use. It is the purchaser's responsibility to know the ordinances and laws of their state or county and to fully comply with them. Dismiss
Reviews
There are no reviews yet.