Additional information
Weight | 5 oz |
---|---|
Dimensions | 4 × 8 × 1 in |
HOSE LENGTH | 30 INCH, 46 INCH |
$59.95 – $69.95Price range: $59.95 through $69.95
Weight | 5 oz |
---|---|
Dimensions | 4 × 8 × 1 in |
HOSE LENGTH | 30 INCH, 46 INCH |
You must be logged in to post a review.
A quality water, oil and odor filter system designed to protect your PCP’s! Consider selecting the combinations that come with the extra-length fill whip so you can stand your filter up and down and still have plenty of slack to connect to your PCP.
Whether you are using a hand pump or a personal compressor it is vitally important that only clean dry air be introduced in your air reservoir.
Made from high-quality aircraft aluminum and is rated for safe use.
Don’t make the mistake of not drying your air as it will destroy regulators as well as your aluminum pressure vessels.
Available with a 47″ high-quality stainless steel fitting hose to allow for convenient filling of your PCP.
For G1 G2 & G30 Variants
Hajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes two of my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
Hajimoto Flex Reg on 22ci Aluminum 3K for the G1
Introducing a Hajimoto Productions Exclusive offer!
22ci/360cc/.36L Aluminum Tank 3000PSI
Newly redesigned unit
Now has a high pressure and low pressure burst discs!
Flex 22 Configuration For Generation 1 Gauntlet .177/.22 Cal
Stock .177/.22 | 3000/1100PSI Regulator
Flex 22 .177/.22 |3000/700 to 1500PSI
Flex 22 Configuration For Generation 1 Gauntlet .25 Cal
Stock .25 | 3000/1900PSI Regulator
Flex 22 .25 | 3000/1500 to 2300PSI
If you are looking to add an externally adjustable reg to your Gauntlet 2, take a look at swapping your current fixed reg to the Flex reg found HERE
Installs on the Gauntlet with minor tank shroud modifications. (The Gauntlet 2 is shown to give an idea of what modification needs to happen and that is simply a hole drilled in the bottom of the plastic tank shroud for the fill nipple.
A 22ci aluminum 3000PSI cylinder with externally adjustable Ninja Flex Reg for your Umarex Gauntlet1! The volume of air in these 22ci tanks over the 13ci is mind-blowing!
The diameter of the tank is 54-55mm across so a modification to the forearm is required on a Gauntlet 1. I do offer a tank shroud modification service for Gauntlet 1 owners that can be added to a build or provided as a mail-in service.
The Gauntlet 2 forearm slide right over without any issue. Only one access hole needs to be drilled so the fill port is accessible at the bottom.
Consider picking up our extended foster fill adapter to make coupling and filling a breeze.
The Power Flex Combo allows the user to externally adjust the regulator output pressure on the fly with an adjustment range of 800PSI!
When installing the Flex 22 on the Umarex Gauntlet. Tighten the degassed tank and regulator assembly fully to the rifle, then back it off until the fill port is on the bottom and the gauges are left and right. Now fill the bottle with air and all will tighten up solid. Proper alignment will be achieved before the 360° maximum rotation limit is realized.
Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!
Because of practical limitations, regulator output will be +/- 50PSI (3.5bar) within the requested output.
Air Stripper, Tension Spring and Baffle Stack
UPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.
Replacement Air Stripper 0-ring is 14mm x 1.5mm
Copyright All rights reserved Hajimoto Productions LLC 2025
Proudly powered by WordPress . Theme: multipurpose shop by eDataStyle.Please be sure to understand our return policies prior to making your purchases. All products offered on our website are intended for use on airguns only. It is a violation of Federal Law to use a product in a manner inconsistent with its intended labeling or use. It is the purchaser's responsibility to know the ordinances and laws of their state or county and to fully comply with them. Dismiss
Reviews
There are no reviews yet.