HP Avenger Exp Mag .22 RED/BLACK

Related products

• 

  $159.00 – $169.00

  5/8″-18UNF Threaded Unit

  Flex Reg Hajimoto Configurations

  Rated 4.00 out of 5

  $159.00 – $169.00

  

  

  Ninja Paintballs’ Flex Reg with Custom Gauntlet Configuration.
  Say goodbye to only one fixed output pressure!
  The user has an 800 – 900 psi adjustment swing!
  Requires minor forestock modification.
  The regulator thread is 5/8-18UNF (Bottle Thread) and Typical Paintball Threads of .825-14 NGO (PCP Thread).
  

  Please note the Flex regulator can be used with any Air, Co2, or Nitrogen driven air gun not just the Gauntlet,  providing it has the correct threading.

  The Ninja Flex regulator is available in any 900 psi spread to a maximum of 3100 psi output but for the Gauntlet select from the proper configuration.
  If you select the Custom Configuration, you will need to use the NOTES above to communicate what you want the maximum output to be.

  How to read the below configurations
  Example: Flex Reg .22 | 4500/1600 to 2400 psi
  Flex Reg .22 = Regulator Type for .22 caliber
  4500/ = The bottle’s maximum fill pressure
  1600 to 2400 psi = The output range of the Flex Reg

  Flex Reg Configuration For Generation 1 Gauntlet .177/.22 Cal
  Stock .177/.22 | 3000/1100PSI Regulator
  Flex Reg .177/.22 |3000/600 to 1500PSI

  Flex Reg Configuration For Generation 1 Gauntlet .25 Cal
  Stock .25 | 3000/1900PSI Regulator
  Flex Reg .25 | 3000/1500 to 2400PSI

  Flex Reg Configuration For Generation 2 Gauntlet .22 Cal
  Stock .22 | 4500/1900PSI Regulator
  Flex Reg .22 | 4500/1500 to 2400PSI

  Flex Reg Configuration For Generation 2 Gauntlet .25 Cal
  Stock .25 | 4500/2100PSI Regulator
  Flex Reg .25 | 4500/1500 to 2400PSI

  Flex Reg Configuration For G30 Cal
  Stock .30 | 4500/2800PSI Regulator
  Flex Reg .30 | 4500/2100 to 3100PSI

  Comes with a dedicated Spanner Wrench for power adjustment. MADE IN THE USA!

  Select options

• 

  $28.00

  HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2

  Rated 5.00 out of 5

  $28.00

  Part fits either the original Gauntlet or the Gauntlet 2

  You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.

  Air Stripper comes with o-ring and silicone grease for installation.

  Select options
• Sale!

  

  $75.00 – $93.00

  Gauntlet STK

  Super Tune Kit (STK) for Gauntlet 1 and 2

  Rated 5.00 out of 5

  $75.00 – $93.00

  THIS ITEM IS NOT DESIGNED FOR THE GAUNTLET 30
  IT HAS ITS OWN HAMMER PRELOAD ADJUSTER STOCK

  The single largest performance increase modification item for the Gauntlet. The Super Tune Kit allows complete power adjustment which opens all the possibilities of lower or higher foot-pounds (FPE) of energy for whatever the user desires. Do you need only 5FPE no problem back off the adjustment using a 5/64″ allen wrench and you are only delivering 5FPE and will realize over 200 shots on a stock bottle fill of 3000PSI!

  Want 27-30FPE for dropping that 20lb trash bandit, no problem, crank up the adjuster using a 5/64″ allen wrench and you instantly have the power necessary for either long range or high energy delivery on target. The use of a chronograph is required in order to know what the rate of travel is of the projectile. (Power examples given are the .22 caliber version Gauntlet 1) 

  For the Gauntlet 1 and Gauntlet 2. Be sure to select the proper generation as there is a difference and improperly selected kits are not returnable.
  BE SURE TO SELECT THE CORRECT GENERATION GAUNTLET

  CONTENTS:

  • Adjuster Plug Assembly.
  • Smaller, Lighter Composite Poppet.
  • Hajimoto Hammer Spring (Black Long)
  • Lighter Trigger Spring (Bright Small).
  • 5/64″ Allen Wrench For Adjusting Power.

  The single largest performance increase modification item is available for the Gauntlet 1 and Gauntlet 2.
  Consider adding the o-ring kit so you have all that you need should one of the factory o-rings get damaged during the kit installation, see option below.

  Be sure to follow my written instructions in the document below.
  Use the video to install but follow these written instructions to adjust and tune the STK:

  Written Detailed Tuning Instructions for the STK

  More details below.
  Always read the content below because any revised instructions, video, photos, or other links will be there.

  Select options