Adjustable Butt Stock
$60.00
SPECS
• Precision fit for military specification buffer tubes (diameter = 1.15″ / length = 7.25″)
• Material: OverMolded® rubber / reinforced polymer
• Color: Black
FEATURES
• Perfect compatibility with Hogue OverMolded grips and forends
• Light-weight skeletonized reinforced polymer construction
• Anti-rattle and beard-safe design
• Collapses to user’s preferred shoulder position
• Polymer cap provides snag-free shouldering
• Rubber/polymer hybrid butt pad cushions recoil
• Multiple swivel sleeve and sling mounting positions
Additional information
Weight | 8 oz |
---|---|
Dimensions | 8 × 2.5 × 5 in |
You must be logged in to post a review.
Related products
-
Umarex Gauntlet Regulator Shim Pak
$18.50Select optionsHajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
-
Gauntlet 1 and Gauntlet 2
Umarex Gauntlet Tune O-ring Kit
$17.00Select optionsHajimoto Productions Tuning O-ring kit for the Gauntlet and Gauntlet 2
Now includes my “NO RING” pellet probe seals as HP-1 rather than the typical high wear donut orings.
I have put together the most common o-rings that fail during a tuning session. Most of the stock o-rings for the internals will gouge when the airgun is disassembled, this kit will allow you multiple attempts should any of the o-rings fail. Please note that the .30 caliber uses completely different internal o-rings than all previous Gauntlet Models including the .30 cal exclusive transfer port orings Which will be bagged as TP.
Some of the NO-Ring seals have the leading edge precision ground.
These tapered / precision ground types need to be installed as shown below
(Images are of the .30 caliber NO RING)
You get:
- 2 of pellet probe NO-ring seals.
- 2 sets of barrel o-rings.
- 2 sets of tank block o-rings.
- 2 of valve body o-rings.
-
HP Air Stripper 2.0 For Umarex Gauntlet 1 and 2
Rated 5.00 out of 5$28.00Select optionsPart fits either the original Gauntlet or the Gauntlet 2
You must apply a liberal amount of silicone grease or other synthetic lube on the air strippers o-ring. Failure to do so will cause the o-ring to grip the dry interior of the shroud and cause damage to and break the air stripper. Please read the provided instructions.
Air Stripper comes with o-ring and silicone grease for installation.
Reviews
There are no reviews yet.