Description
Please be sure to measure your free area or clearance between the bottom of your scope to the bottom of the magazine well.
LOADING THE MAGNETIC VERSION
The MROD, Expanded Magazine
$35.00
Here is a high-quality, high-capacity magazine designed to fit the Benjamin Marauder rifle in .177, .22, and .25 calibers. This magazine extends your capabilities by increasing the number of shots before requiring a reload.
WILL NOT FIT THE BENJAMIN MARAUDER PISTOL
New magnetic lid. This magazine fits under high-scope rings and some medium-scope rings. Your scope may need to be moved forward or back to clear the turret bell.
Remember we stock adjustable height scope rings by WestHunter, EagleVision, and FX, be sure to snag a set if you are worried about clearance issues plus adjust rings allow you to keep your scope optically centered leaving all the turret adjustment-free to use when you need it.
Features
- Redesigned magnetic lid design available for .177, .22, and in .25 calibers now.
- Drop in loading.
- Easy partial fill design.
- .177 – 21 shots, an increase of 110% over the stock mag. The magazine’s height is 50.25MM (1.978″)
- .22 = 17 shots, an increase of 70% more shots over the stock mag. The magazine’s height is 50.25MM (1.978″)
- .25 = 14 shots which is an increase of almost 60% more shots over the stock mag The magazine height is 48.02MM (1.890″)
WATCH THE VIDEO BELOW ON HOW TO LOAD MAGAZINE
You must be logged in to post a review.
You may also like…
-
Sold out!
$99.00Eaglevision INS Mount
Infinity INS Elevation Adjustable Scope Mount 30mm Ring Picatinny
$99.00Read more
Eaglevision has designed and developed an amazing scope mount that allows the scope to move vertically along a guided path. The mount is lockable in different positions using two screws. This mount can be used as a low profile or be adjusted to the high profile too if your scope objective is too close to your rifle barrel or shroud. These mounts resolve a lot of problems for shooters who like to shoot long range and often run out of adjustment clicks on their turrets.
The mount can also come in handy if you have not been able to use your favorite scope due to lack of space between the rings or the odd position of your dovetail or Picatinny rail on your gun. We are very proud of this product as it became a “must-have” for people who love their bullpups.
The best application of this mount however is for people who want to reach out further than their ordinary mounts allow them to. By keeping the front mount at its lowest and elevating the rear mount to the highest point you can zero in your gun far beyond your normal mounts allows you to, without using the clicks on your turrets hence keeping the optical center of your scope intact (the ideal situation for long-range shooting).Another great feature is these mounts allow the scope to be lifted to allow for large or expanded magazines.
Item includes:
- 2 x infinity scope mount.
- 2 x allen key (different sizes).
- 4 x spears screws.
- 1 x large spear screw.
- Protection ring fabric.
- Waterproof case.
-
$79.00FX No Limit Scope Rings 1″, 30mm and 34mm – 30mm/Picatinny
$79.00Add to cartTube/Rail Option: 30mm/Picatinny
-
$79.00FX No Limit Scope Rings 1″, 30mm and 34mm – 30mm/Dovetail
$79.00Add to cartTube/Rail Option: 30mm/Dovetail
Related products
-
$47.00Air Stripper, Tension Spring and Baffle Stack
HP Strip Stak Pak for Avenger
$47.00Select optionsUPDATE: The newer avengers have a screw-on barrel shroud and an end cap that is a two-piece unscrewable but the STP still fits and works without an issue. unscrew the shroud rather than the little screw shown in the video and simply unscrew the baffle washer array off the end cap and you are good to go.
Strip Stak Pak for the Avenger
A six piece kit that includes an efficient multiport air stripper that strips and channels air away from the pellet to allow for a more stable and less turbulent pellet launch from the muzzle. The kit also provides baffle chambers to help remove both noise and turbulence in the air stream. The end result is a more laminar air stream which reduces projectile instability and as a secondary benefit, reduces the report of the rifle. This kit is 100% compatible with the stock end cap or the DonnyFL A50 adapter.
Air Stripper comes with o-ring and silicone grease for installation. The installation video for the Umarex Origin Strip Stak Pak is exactly the same so you can follow the installation video below.Replacement Air Stripper 0-ring is 14mm x 1.5mm
-
$110.00Fits the G1, G2/G2SL or G30/G30SL
Real 2 Stage Trigger for the Gauntlet
$110.00Select optionsFull-fledged 2-stage trigger for the Umarex Gauntlet 1, 2, G30, bolt or sidelever variants. This trigger is a direct replacement for the single-stage trigger that ships with the Umarex Gauntlet. This trigger is a straightforward install that will increase the accuracy of your shooting due to a more predictable and consistent breakpoint.
- The Trigger Is Stainless Steel 17-4 Through Hardened
- The Trigger Shoe Is Aluminum 6061-T6
Please see the installation video below for more details.
Super Tune Kit Users
You must use the stock trigger return spring with the two-stage trigger as the trigger spring that comes with the Super Tune Kit is too light to be effective with the two-stage trigger. -
$30.00Intended for higher power builds
High Travel Valve Stop For Umarex Gauntlet 1 or 2
$30.00Select optionsThis part replaces part #19 and allows for greater valve dwell producing more power to be produced at higher regulator pressure settings.
The .22 caliber HTVS for the Generation 1 Gauntlet fits both the .177 and .22. Do not order Generation 1 HTVS for the Generation 2 Gauntlet, they are not the same
Reviews
There are no reviews yet.