-
Price range: $14.00 through $18.00Adapter for NateChrony V2
NateChrony Variable Adapter
Price range: $14.00 through $18.00Select options
A variable adapter for barrels that are not threaded. The variable adapter is simply pushed onto the end of the barrel & tightened in place with the thumb screws.
The bore & outer barrel MUST be concentric! Otherwise damage or injury could occur.Select the maximum outer diameter of the barrel from the options. The adapters can be adjusted from its maximum diameter down to the minimum diameter by changing the internal inserts.
The barrel MUST make contact at FOUR points, as close as possible to the top & bottom of the barrel. If the adapter is making contact at the middle of the barrel mis-alignment can occur.
Thumb screws are aluminum & supplied with either knurled or printed tabs.
Price is for 1 adapter, with 1 set of screws.
-
Sold out!
$40.00NateChrony SmartTarget
NateChrony SmartTarget Accessories
$40.00Read moreAccessories
The NateChrony SmartTarget has 6 outputs – 1 for addressable LEDs, and 5 programmable outputs. These accessories connect to these outputs to indicate hit detection, shot placement, and can drive external equipment via relay boards.
Short Range LED Kit – Cross
The short range kit features 5 LEDs in a cross shape, with spacing of 50mm. This makes it convenient and compact for shorter ranges, typically 50-100m. It connects directly to the SmartTarget outputs via a supplied 1m cable.
The middle LED will show green on a center hit, red on the outer LEDs when struck at the outer edges, and orange on the outer LEDs when struck between the center and outer edges.
The cross can be mounted to a surface behind the target (to avoid spalling) via tape, bands or zip ties.
Long Range LED Kit – 4+2 LEDs
The long range kit features 4 LED modules (and 2 spare), which are connected to either the 4-connector board or can be daisy-chained to each other, via the supplied 30cm cables and connectors. This allows spacing between LEDs of up to 60cm, ideal for easy recognition at long ranges.
All four LEDs will display green on a center hit, show red when struck at the outer edge, and orange when struck between the center and outer edge.
The LEDs are supplied with quality 3M double sided tape, and are stuck to the rear surface of the target, or another surface behind the target face.
Long Range LED Kit – 10+2 LEDs
This kit is the same style as the 4+2 above, but with more LEDs and larger 10x connector board. This allows for larger and creative designs, with different LED colours and behaviours, such as a doe or buck with highlighted antlers and eyes.
DIY LED Kit – 10+2 LEDs
The ultimate in flexibility – we provide the LED boards and snap connector blocks, you then wire and connect them in any style you want. This is perfect for target makers or people that want to do customise their targets, and really transform a boring target into a fully interactive one.
LEDs will need wires soldered to the boards, however the supplied snap connectors make interconnecting and LED replacements quick and easy. You will also need to mount them using tape, or they can be drilled and screwed into place.
Informational videos below.
-
$85.00NateChrony SmartTarget
NateChrony SmartTarget
$85.00Select optionsAdd some smarts to your target!
Mount the NateChrony SmartTarget to the back of your existing targets, when the target is struck by an object & moves – the SmartTarget will detect the movement, register the shot, and based on the way your target moves – tell you approximately where the shot landed.SmartTarget
The NateChrony SmartTartget has an inbuilt motion sensor that detects movement, by analysing this movement it can detect being hit, and also the possible location of that hit. Mounting to a free moving target such as a hanging gong is highly recommended – as it can freely move in left-right and up-down directions.
The SmartTarget can be mounted to any surface, and used to detect any object – airguns, firearms, baseball… If you need to detect movement and strike location, the SmartTarget is for you.
The features will be rapidly improving as we get customer feedback and develop additional features.Features
- Mounts to any target with double sided tape, or screws
- Center hole on case to assist with accurate placement
- Standard 10 ring target face display for shot placement
- Score display
- Match Mode: Track and save multiple shots
- Calibration: can be adjusted to match the movement of every unique target
- Sensitivity: can be adjusted for low power/long range, or high power/short range
- External Lights: ultra high brightness LED accessories available, so superb visibility at range
- Programmable Lights: we can program any lighting effects you can imagine
Accessories
- Short Range/Cross: 5 LEDs in a cross with 60mm spacing for 50-100m range
- Long Range LEDs: 4+2 or 10+2 LEDs that can be spaced at 600mm
- DIY Lighting Kit: 10+2 LEDs that you can wire together to create custom designs
Note: Accessories are optional
Requirements, Specifications, and more below.
-
Price range: $130.00 through $165.00NateChrony V2.5 and SteadyShot Versions
NateChrony V2.5 and SteadyShot Versions
Price range: $130.00 through $165.00Select optionsTake your training to the next level – we’ve added motion sensors to the NateChrony!
We’ve taken the best Chronograph on the market to the next level – by adding a 6-axis inertial measurement unit to it. You can now see how your muzzle is moving when you shoot – is it steady? is the movement smooth? are you consistent?
The SteadyShot also has the advanced software with new features:
- Full automatic fire measurement, up to 1,250 shots per second.
- Airsoft specific screens:
fps & J, with a rate of fire for each shot
Pre-programmed & quick change bb weights - Field mode – quickly check if you’re above/below 3 programmed speeds/powers
You can see your movement on each axis via 3 separate graphs:- Left/Right
- Up/Down
- Back/Forth
You can also view your movement in a 3 dimensional line graph – showing how you moved in space.
- All NateChrony adapters are fully compatible with the SteadyShot.
Requirements:
You’ll need this stuff to use the NateChrony – typically if you have a mobile phone you’re set!
- If using a mobile phone/tablet, it should be less than 5 years old & up to date.
- Working knowledge of your device, including browser and internet technologies
- Working knowledge of any additional security software installed on your device
- A 5v standard USB power source
- A device (phone/tablet) that can connect to a Wi-Fi hotspot, that does not have internet access
- A web browser that can connect to a HTTP (not HTTPS) web page and run JavaScript
- You can test your device here, ensure the page loads and displays a speed and power value, and when clicking on Menu – Shoot, you hear the speed and power readout
NOTE: if you have software or settings on your device that does not permit this – you may have issues
