NateChrony SmartTarget
$40.00
Accessories
The NateChrony SmartTarget has 6 outputs – 1 for addressable LEDs, and 5 programmable outputs. These accessories connect to these outputs to indicate hit detection, shot placement, and can drive external equipment via relay boards.
Short Range LED Kit – Cross
The short range kit features 5 LEDs in a cross shape, with spacing of 50mm. This makes it convenient and compact for shorter ranges, typically 50-100m. It connects directly to the SmartTarget outputs via a supplied 1m cable.
The middle LED will show green on a center hit, red on the outer LEDs when struck at the outer edges, and orange on the outer LEDs when struck between the center and outer edges.
The cross can be mounted to a surface behind the target (to avoid spalling) via tape, bands or zip ties.
Long Range LED Kit – 4+2 LEDs
The long range kit features 4 LED modules (and 2 spare), which are connected to either the 4-connector board or can be daisy-chained to each other, via the supplied 30cm cables and connectors. This allows spacing between LEDs of up to 60cm, ideal for easy recognition at long ranges.
All four LEDs will display green on a center hit, show red when struck at the outer edge, and orange when struck between the center and outer edge.
The LEDs are supplied with quality 3M double sided tape, and are stuck to the rear surface of the target, or another surface behind the target face.
Long Range LED Kit – 10+2 LEDs
This kit is the same style as the 4+2 above, but with more LEDs and larger 10x connector board. This allows for larger and creative designs, with different LED colours and behaviours, such as a doe or buck with highlighted antlers and eyes.
DIY LED Kit – 10+2 LEDs
The ultimate in flexibility – we provide the LED boards and snap connector blocks, you then wire and connect them in any style you want. This is perfect for target makers or people that want to do customise their targets, and really transform a boring target into a fully interactive one.
LEDs will need wires soldered to the boards, however the supplied snap connectors make interconnecting and LED replacements quick and easy. You will also need to mount them using tape, or they can be drilled and screwed into place.
Informational videos below.
Sold out!
Related products
-
Sold out!
$18.50Umarex Gauntlet Regulator Shim Pak
$18.50Read moreHajimoto Productions Regulator Shim Kit For Umarex Gauntlet
I have put together a very easy and complete stainless steel shim kit so you can adjust your Gauntlets Regulator output. The shims that I have included give you a wide range of adjustability to mix and match different thicknesses to get the regulator to output exactly what you want. The shim kit comes with easy to follow instructions which guide you through the process as to what shims you need to add to typically achieve my recommendations for each Gauntlet Caliber.
The shim kit contains:
- 2 – #5 Shims.
- 1 – #3 Shim.
- 2 – #2 Shims.
(Two #2’s = One #4 | Two #5’s = One #10 | One #5 + One #3 = One #8, and so on)
To take a stock G1 .177/.22 from the stock 1100-1050PSI to my recommended 1350-1400PSI you would add two (2) #5 shims (10).
To take a stock G1 .25 from the stock 1900-1950PSI to my recommended 2100-2200PSI you would add one (1) #3 shim (3).
The included two #2 shims are for minor adjustments if you have a finicky regulator.DETAILED LESSON/EXAMPLE:
Let’s say your .22 Gauntlets regulator only puts out 1300PSI after installing the two #5’s when it should be 1350 to 1400PSI, you would add one #2 for a total of 12 to help get it there. If after the addition of the one #2, you’re still 50psi short so you would pull out the #2 and use the #3 for a total of 13.Always use a regulator output tester to confirm the output pressure of your regulator. It is the only safe and sure way to properly adjust the pressure of your regulator.
You have to fill and purge so the Belleville washers settle into the new preload. Be sure to slow fill your bottle the first time only to 500PSI and then purge it, fill slowly a second time to 1000, and then purge fill the final time slowly and watch to be sure the reg has settled and does not exceed your target pressure. If it does exceed your target pressure, stop filling, purge and shim less.
If you rapid fill, there is a good chance you will pop your burst disc.
-
Sale!
Original price was: $17.95.$14.00Current price is: $14.00.Stock Umarex Magazine
Umarex Gauntlet Rotary Magazine
Original price was: $17.95.$14.00Current price is: $14.00.Select optionsThe Gauntlet Rotary Magazine advances each pellet with the operation of the bolt on the Umarex Gauntlet PCP air rifle.
Features
- .22 = 10 shots
- .25 = 8 shots
- .30 = 7 shots
-
$110.00For G30 and G30SL
G30 Barrel Shorten and Recrown
$110.00Select optionsService to reduce barrel length removing the barrel choke making the barrel better for slugs. Service
The service executes the following:
- Reduce barrel length by 2.5″ to remove the choke.
- Recrown barrel.
- We provide a new shorter replacement barrel shroud.
This can be added to a custom build order or a send-in modification request. Customers who wish to send in their barrel for service can ship either the entire rifle or just the barrel, barrel shroud, and end cap. The barrel will be heavily cleaned and coated with silicone oil to protect the surfaces for the trip home.
Once the order is received, a follow-up email will be provided. Depending on the service request, the response will contain detailed shipping instructions, including the shipping address and other pertinent information required on the label for the service request being shipped to us.
This service price does not include shipping or parts. Shipping costs to return your PCP or PCP parts will need to be calculated and communicated to you before the order ships back.The reduction of an airgun barrel typically results in a decreased rate of travel of 15-20 ft/s per inch.
Any outstanding balance must be paid before we ship out the service order.
Reviews
There are no reviews yet.